Related Manuals for Fluke 301D
Summary of Contents for Fluke 301D
- Page 1 301D/301E Clamp Meter Users Manual Nov 2022 (English) © 2022 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of their respective companies.
- Page 2 Fluke authorized resellers shall extend this warranty on new and unused products to end-user customers only but have no authority to extend a greater or different warranty on behalf of Fluke. Warranty support is available only if product is purchased through a Fluke authorized sales outlet or Buyer has paid the applicable international price.
-
Page 3: Table Of Contents
Table of Contents Title Page Introduction .......................1 Contact Fluke ......................1 Safety ........................2 Before You Start .......................2 Battery ........................2 Features/Controls ....................3 Display .......................4 Power .........................5 Auto Power Off ....................5 Backlight ......................5 Power-On Options ..................5 Basic Measurements ....................6 Hazardous Voltage Indicator ................6 AC Voltage Measurement with Test Leads ..............6... -
Page 4: Introduction
Introduction The Fluke 301D/301E Clamp Meter (the Product) measures current and voltage, resistance, continuity, diode, capacitance and frequency. The 301D/301E can measure AC and DC current. Contact Fluke Fluke Corporation operates worldwide. For local contact information, go to our website: www.fluke.com. -
Page 5: Safety
General Safety Information is in the printed Safety Information document that ships with the Product and at www.fluke.com. More specific safety information is listed where applicable. A Warning identifies conditions and procedures that are dangerous to the user. A Caution identifies conditions and procedures that can cause damage to the Product or the equipment under test. -
Page 6: Features/Controls
301D/301E Users Manual Features/Controls Table 1 is a list of features and controls. Table 1. Feature/Control Descriptions 600A Item Description Tactile Barrier Hold Control Knob Display Extends the function selection to yellow items on the control knob. Push >2 s to turn on/ turn off the backlight. -
Page 7: Display
Clamp Meter Before You Start Display Table 2 is a list of the display annunciators. Table 2. Display Item Description Item Description Hazardous voltage Auto Power off Diode test selected Low battery. Replace battery. Continuity selected DC or AC measurement Display hold enabled Farads for capacitance Zero indication... -
Page 8: Power
301D/301E Users Manual Power Two AAA batteries supply power to the Clamp: • To turn on the Clamp, rotate the control knob from OFF to a function. • To turn off the Clamp, rotate the control knob to OFF. Auto Power Off The Clamp automatically powers off after 20 minutes of no use. -
Page 9: Basic Measurements
Clamp Meter Basic Measurements Basic Measurements XW Warning To prevent possible electrical shock, fire, or personal injury: • Hold the Product behind the tactile barrier. • Do not measure current while the test leads are in the input jacks. Hazardous Voltage Indicator When the Product senses a voltage more than ±... -
Page 10: Resistance/Continuity
301D/301E Users Manual Resistance/Continuity To measure resistance or continuity: 1. Turn the control knob to 2. Remove power from the circuit to test. 3. Connect the black test lead to the COM terminal and the red test lead to the VΩ terminal. -
Page 11: Test Diodes
Clamp Meter Basic Measurements Test Diodes W Caution To prevent possible damage to the Product or to the equipment under test, disconnect circuit power and discharge all high-voltage capacitors before you test diodes. To test a diode: 1. Turn the rotary switch to 2. -
Page 12: Amps Dc
301D/301E Users Manual Amps DC XW Warning To prevent electrical shock, do not measure current while the test leads are in the input jacks. Amps DC Measurement with Jaw To measure amps dc: 1. Turn the control knob to . -
Page 13: Maintenance
Contact Fluke Service Have an authorized Fluke Calibration service center service the Product at one-year intervals to maintain optimum performance. Contact your equipment distributor or authorized Fluke Calibration Service Center for any equipment performance failure or to schedule regular maintenance service. -
Page 14: Specifications
301D/301E Users Manual Specifications General Maximum Voltage Between any Terminal and Earth Ground ....300 V Between V/Ω Terminal and COM Terminal ..... 600 V Display (LCD) ............6000 counts, updates 3/sec Battery Type ................. 2 AAA IEC LR03 alkaline Life ................ -
Page 15: Safety
Clamp Meter Specifications Electromagnetic Compatibility (EMC) International ..........IEC 61326-1: Portable, Electromagnetic Environment, IEC 61326-2-2 CISPR 11: Group 1, Class A Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself. Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings... -
Page 16: Accuracy Specifications
301D/301E Users Manual Accuracy Specifications Accuracy is specified for 1 year after calibration, at operating temperatures of 18 °C to 28 °C, relative humidity at 0 % to 90 %. Accuracy specifications take the form of: ±([% of Reading] + [Number of Least Significant Digits]).