Samsung SCX-4521F User Manual page 62

Display Meaning
Low Heat Error There is a problem in
the fuser unit.
Open Heat Error
[Over Heat]
Group Not You have tried to
Available select a group location
(only for SCX- number where only a
4521F) single location
number can be used,
such as when adding
locations for a
broadcast operation.
[Incompatible] The remote machine
(only for SCX- did not have the
4521F) requested feature,
such as a delayed
transmission.
This message also
occurs if the remote
machine does not
have enough memory
space to complete the
operation you are
attempting.
[Line Busy] The receiving party
(only for SCX- did not answer or the
4521F) line is already
engaged.
[Line Error] Your machine cannot
(only for SCX- connect with the
4521F) remote machine or
has lost contact
because of a problem
with the phone line.
Load Document You have attempted
to set up a copy or fax
operation with no
document loaded into
the ADF.
[LSU Error] A problem has
occurred in the LSU
(Laser Scanning Unit).
Memory Dial Full The fax jobs queue in
(only for SCX- the memory is full.
4521F)
Suggested solutions
Unplug the power cord and
plug it back in. If the problem
persists, please call for
service.
Use a speed dial number or
dial a number manually using
the number keypad.
Reconfirm the remote
machine's features.
Try again after a few minutes.
Try again. If the problem
persists, wait an hour or so
for the line to clear and try
again.
Or, turn the ECM mode on.
See "ECM Mode (Error
Correction Mode)" on
page 7.14.
Load a document into the ADF
and try again.
Unplug the power cord and
plug it back in. If the problem
persists, please call for
service.
Cancel unnecessary fax jobs
in the memory.
9.5
Troubleshooting
Display Meaning
Memory Full The memory is full.
(only for SCX-
4521F)
[No Answer] The receiving fax
(only for SCX- machine has not
4521F) answered after
several redial
attempts.
[No Cartridge] The toner cartridge is
not installed.
• The speed dial
Not Assigned
location you tried to
(only for SCX-
use has no number
4521F)
assigned to it.
• The ID you entered
is not assigned.
[No Paper] The paper in the tray
Add Paper has run out.
Operation You are doing the
Not Assigned Add/Cancel operation,
(only for SCX- but there are no jobs
4521F) waiting.
Out of Range The current date and
time you entered is
not correct.
[Paper Jam 0] Paper has jammed in
Open/Close Door the feeding area of
the tray.
[Paper Jam 1] Paper has jammed in
Open/Close Door the fuser area or
around the toner
cartridge.
[Paper Jam 2] Paper has jammed in
Check Inside the paper exit area.
[Power Failure] Power has turned off
then on and the
machine's memory
has not been saved.
Suggested solutions
Delete unnecessary
documents and retransmit
after more memory becomes
available. Alternatively, split
the transmission into more
than one operation.
Try again. Make sure that the
receiving machine is
operational.
Install the toner cartridge.
See "Installing the Toner
Cartridge" on page 2.2.
• Dial the number manually
using the number keypad or
assign the number. For
storing a number, see
"Automatic Dialing" on
page 7.8.
• Enter the correct ID. .
Load paper in the tray. See
"Loading Paper" on page 2.3.
Check the display to see if
there are any scheduled jobs.
The display should indicate
them in Standby mode; for
example, Delay Fax.
Enter the correct date and
time.
Clear the jam. See "In the
Tray" on page 9.2.
Clear the jam. See "In the
Fuser Area or Around the
Toner Cartridge" on page 9.3.
Clear the jam. See "In the
Paper Exit Area" on page 9.3.
The job which you were trying
to do before the power failure
must be completely re-done.