Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Spinner BN 553364
Summary of Contents for Spinner BN 553364
- Page 1 RF plug-in switch (DPDT) Coaxial interface: 29.5-68 USL-D BN 553364 BN 553365...
-
Page 2: Table Of Contents
Content Basic Safety Instructions for SPINNER Broadcast Products ..............3 Intended use ............................. 6 Improper use ............................6 Function ..............................6 Motor drive ............................... 6 SPINNER crank drive ..........................6 Bistable switching property (latching) ....................... 7 Manual override ............................7 Visual position indicator ........................... -
Page 3: Basic Safety Instructions For Spinner Broadcast Products
The following instructions and safety instructions are to be carefully read and followed! The Spinner group makes every effort to keep the safety standard of our products up to date to be able to offer our customers the highest possible degree of safety. Our products are designed and tested in accordance with the relevant safety standards. - Page 4 Doing so can cause short circuits inside the product and/or electric shocks, fire or injuries. 23. Dangerous voltage must not reach the product over the outer conductor / waveguide. Data subject to change without notice │ M36274 │ Issue B 4 / 21 www.spinner-group.com...
- Page 5 36. The operator is responsible for disposing of the product according to national waste disposal regulations. Improper disassembly or disposal may be hazardous. 37. SPINNER RF switches are not equipped with separating equipment for safe disconnection from mains. The user must provide external separation equipment. The mains connector must be de-energized during plugging.
-
Page 6: Intended Use
A capacitor motor with a supply voltage of 230 V AC 50/60 Hz is used to actuate the RF plug-in switch via a special crank gear box developed by SPINNER. Depending on the type of switch the drive control system enables remote switching by means of a control voltage of 230 V AC, 50/60 Hz or 8 to 31 V... -
Page 7: Bistable Switching Property (Latching)
RF plug-in switch from the patch panel. The eccentric position of the strapping plug prevents attachment of the switch in an incorrect assembly position. Data subject to change without notice │ M36274 │ Issue B 7 / 21 www.spinner-group.com... -
Page 8: Data Sheet
USL-interlock I Nominal fuse The circuits must be externally limited to 0.5 A. Connector J2 ** 5 pole SPINNER connector BN 126920, certified according to for mains connection VDE-Reg. No. B687, DIN EN 61984: 2009-11; EN 61984: 2009 Mains connection... - Page 9 4,000 m or 13,120 ft according to IEC EN 60664-1 Protection class I according to IEC EN 61140 IP40 according to IEC EN 60529 IP protection level (all interfaces terminated) Data subject to change without notice │ M36274 │ Issue B 9 / 21 www.spinner-group.com...
- Page 10 Load VSWR, max. 1.0 (no standing wave) No modulation, sinusoidal carrier only Suitable mating connector included Suitable SPINNER mating connector BN 539145 not in delivery! **** At room temperature and nominal voltage 230 V AC ***** Extended temperature range on request Power handling vs.
-
Page 11: Dimensions (All Dimensions In Millimeters)
Detail "X" Circuit diagram RF connection RF position I: A-B / C-D RF position II: A-D / B-C Ground connection ~116 +10 to disconnect the connector Data subject to change without notice │ M36274 │ Issue B 11 / 21 www.spinner-group.com... -
Page 12: Circuit Diagrams
Circuit diagrams No. B41003-CD Issue G, valid for BN 553364 Data subject to change without notice │ M36274 │ Issue B 12 / 21 www.spinner-group.com... - Page 13 No. B41001-CD Issue E, valid for BN 553365 Data subject to change without notice │ M36274 │ Issue B 13 / 21 www.spinner-group.com...
-
Page 14: Storage
Failure to observe could result in death or serious injury. Only trained electricians should install SPINNER RF plug-in switches in accordance with applicable national and international safety rules and regulations. -
Page 15: 10.1 Mechanical And Rf Installation
Do not stress the RF connectors Use transportation and lifting gear approved to carry at least 15 kg only. Do not stress the connectors and the manual override. Data subject to change without notice │ M36274 │ Issue B 15 / 21 www.spinner-group.com... -
Page 16: 10.2 Electrical Installation
• Relieve all connections to the RF plug-in switch from any bending torque, e.g. caused by heavy cables or assemblies. Avoid sharp bends and tensile load. Data subject to change without notice │ M36274 │ Issue B 16 / 21 www.spinner-group.com... - Page 17 EN 61984: 2009 Approved plug connector BN 126920 Please attend the valid safety rules for assembling! Design is subject to change without notice Strain relief for cable Data subject to change without notice │ M36274 │ Issue B 17 / 21 www.spinner-group.com...
-
Page 18: Commissioning
Before you start, ensure to read and understand the Basic Safety Instructions and the additional safety instructions on personal safety that appear in relevant parts of this manual. Failure to observe could result in death or serious injury. Only trained electricians should commission SPINNER RF plug-in switches. WARNING Electric shock hazard Electric shock can cause severe burns and fatal injuries. -
Page 19: Maintenance
Before you start, ensure to read and understand the Basic Safety Instructions and the additional safety instructions on personal safety that appear in relevant parts of this manual. Failure to observe could result in death or serious injury. Only trained electricians should demount SPINNER RF plug-in switches. WARNING Electric shock hazard Electric shock can cause severe burns and fatal injuries. -
Page 20: Disposal
Use safety gloves and handle carefully. ATTENTION The supplied packaging is reusable and required for transportation. If not available, contact SPINNER before starting demounting. Use transportation and lifting gear approved to carry at least 15 kg only. Do not stress the connectors and the manual override. -
Page 21: Environmental Friendy Usage Period
SPINNER GmbH • Headquarters Erzgiessereistr. 33 80335 München Germany Phone +49 8912601-0 E-mail: info@spinner-group.com Web: www.spinner-group.com Spinner Telecommunication Devices (Shanghai) Co., Ltd 351 Lian Yang Road Songjiang Industrial Zone Shanghai 201613 China Phone +86 21 5774 5377 E-mail: info-china@spinner-group.com Web: www.spcn.cn...
Need help?
Do you have a question about the BN 553364 and is the answer not in the manual?
Questions and answers