The following instructions and safety instructions are to be carefully read and followed! The Spinner group makes every effort to keep the safety standard of our products up to date to be able to offer our customers the highest possible degree of safety. Our products are designed and tested in accordance with the relevant safety standards.
Page 4
Doing so can cause short circuits inside the product and/or electric shocks, fire or injuries. 23. Dangerous voltage must not reach the product over the outer conductor / waveguide. Data subject to change without notice │ M36311 │ Issue F 4 / 18 www.spinner-group.com...
Page 5
36. The operator is responsible for disposing of the product according to national waste disposal regulations. Improper disassembly or disposal may be hazardous. 37. SPINNER RF switches are not equipped with separating equipment for safe disconnection from mains. The user must provide external separation equipment. The mains connector must be de-energized during plugging.
The drive and the basic switch element (rotor) are connected by a special gear which has been developed by SPINNER. With the hypocycloidic gear it is achieved that the torsional moment and angular velocity changes within the range of rotation.
To ensure equipotential bonding with other plant components, connect the marked earthing terminal to the main earthing busbar with a copper lead (min 6 mm²). Data subject to change without notice │ M36311 │ Issue F 7 / 18 www.spinner-group.com...
25 pole connector according to DIN 41652 / IEC 807-2 interlock contacts and signaling BN 512690C0001: 12 V DC ± 10% Operating voltage BN 512690C0002: 21.6 to 28 V DC BN 512690C0062: 21.6 to 28 V DC BN 512690C0001: 2 A Operating current, typ.
Page 9
Above this ambient temperature the maximum input power must be reduced as shown in the diagram. 100% Ambient temperature [°C] Data subject to change without notice │ M36311 │ Issue F 9 / 18 www.spinner-group.com...
2x M4 / 6 deep on both sides Position indication Ground connection RF connection RF position I: 1-2 / 3-4 RF position II: 1-4 / 2-3 Data subject to change without notice │ M36311 │ Issue F 10 / 18 www.spinner-group.com...
Circuit diagrams No. B22676-CD Issue C, valid for BN 512690C0001 Data subject to change without notice │ M36311 │ Issue F 11 / 18 www.spinner-group.com...
Page 12
No. B24140-CD Issue D, valid for BN 512690C0002 and BN 512690C0062 Data subject to change without notice │ M36311 │ Issue F 12 / 18 www.spinner-group.com...
Failure to observe could result in death or serious injury. Only trained electricians should install SPINNER RF switches in accordance with applicable national and international safety rules and regulations.
Do not use the interlock loop for operational switch-off of the transmitters. Connect all transmitters to the interlock loop to avoid RF switch damage. Hot switching is not permitted. Data subject to change without notice │ M36311 │ Issue F 14 / 18 www.spinner-group.com...
Before you start, ensure to read and understand the Basic Safety Instructions and the additional safety instructions on personal safety that appear in relevant parts of this manual. Failure to observe could result in death or serious injury. Only trained electricians should commission SPINNER RF switches. WARNING Radio Frequency Hazard Radio Frequency Power can cause burns, eye injuries and electric shock.
Before you start, ensure to read and understand the Basic Safety Instructions and the additional safety instructions on personal safety that appear in relevant parts of this manual. Failure to observe could result in death or serious injury. Only trained electricians should demount SPINNER RF switches. WARNING Radio Frequency Hazard Radio Frequency Power can cause burns, eye injuries and electric shock.
The supplied packaging and all protection caps are reusable and required for ATTENTION transportation. If not available, contact SPINNER before starting demounting. Do not stress the connectors and the manual override. Follow the procedure described in chapter 10 in reverse order.
Need help?
Do you have a question about the BN 512690C0001 and is the answer not in the manual?
Questions and answers