Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for twaudio SFV20
Summary of Contents for twaudio SFV20
- Page 1 Assembly SFV20 Instructions...
- Page 2 If you lend your product to another party, inform that party of the safety-related operating pro- cedures and hand over this assembly guide. If you require additional copies of this manual, you can obtain them free of charge from TW AUDiO or download them from www.twaudio.de Instructions in this setup manual...
- Page 3 Notes on the products Before using the rigging frame , carefully read the assembly instructions and keep the instruc- Read manual tions in a safe place together with the SFV20 rigging frame . before use! General Information Assembly Guide: OM -SFV20 Version 2.0 d, 11/2022...
-
Page 4: Table Of Contents
Assembly Instructions SFV20 Table of contents 1. Safety | Intended use ...................... 5 2. Overview ........................7 Components ......................7 3. Technical specifications ....................8 Data sheet ....................... 8 4. Commissioning ....................... 9 Setup ........................9 Wind load ........................ 9 Secondary safety component ................ -
Page 5: Safety | Intended Use
The SFV20 rigging frame may only be used by trained and qualified personnel. Personnel must check the SFV20 for its full suitability before each use. WARNING When visible damage to any part of the SFV20 rigging frame is detected, it must be decom- missioned immediately. WARNING... - Page 6 WARNING When installing the SFV20 rigging frame, be careful not to pinch or twist the power cables or other cables of the VERA20 loudspeakers! The respective national electrotechnical regu- lations apply.
-
Page 7: Overview
2. Overview Components Figure 2.1 - Overview SFV20 rigging frame - Surface powder-coated VERA LA900 Load adapter with shackle Captive Quick-locking pins When the SFV20 rigging frame is delivered from the factory, the quick-locking pins are in „Storage Position“. NOTE... -
Page 8: Technical Specifications
Assembly Instructions SFV20 3. Technical specifications Data sheet 230 kg [507.1 lbs] at safety factor 10 before maximum load capacity breacking point correspond to e.g. 9 VERA20 elements Dimensions (h x w x d) 100 x 550 x 600 mm [3.94 x 21.65 x 23.62 in] Weight 6,8 kg [15 lbs.]... -
Page 9: Commissioning
Assembly Instructions SFV20 4. Commissioning Setup The SFV20 rigging frame is designed for hanging operation. TW AUDiO provides a wide range of accessories to securely attach the module to crossbeams, motor lifts, etc. in a suspended position. Please note that setting up the system setups always requires two persons! -
Page 10: Secondary Safety Component
For the second independent safety component, attach another VERA LA900 load adapter with shackle at point D to the rigging frame. Mount it directly behind the first load adapter. Attach both VERA LA900 load adapter using two quick-locking pins each to the SFV20 rig- WARNING... -
Page 11: Preparing Vera20 Loudspeaker For Rigging
Assembly Instructions SFV20 Preparing VERA20 loudspeaker for rigging 1. Use the EASE Focus software to determine the number of VERA20 loudspeakers suitable for your application. NOTE 2. Each VERA DLV20 transport dolly will hold four VERA20 loudspeakers. Provide the num- ber of loaded transport dollies required for your application. - Page 12 Assembly Instructions SFV20 6. Check that all splay links are fully extended and that all quick-locking pins on both sides are always completely inserted! WARNING Figure 4.4.2 - VERA20 loudspeakers on VERA DLV20 transport dolly...
- Page 13 Assembly Instructions SFV20 7. Use the EASE Focus software to determine the angle values suitable for your application. NOTE 8. Move the right-hand sliders on all speakers to the previously determined angle value. 9. Check that all quick-locking pins are always completely inserted! WARNING 12°...
-
Page 14: Using The Vera La900 Load Adapter
Assembly Instructions SFV20 Using the VERA LA900 load adapter quick-locking quick-locking Figure 4.5.1 - VERA LA900 load adapter Two quick-locking pins are attached to the VERA LA900 load adapter. Attach the VERA LA900 load adapter using both quick-locking pins to the SFV rigging frame! WARNING Use the EASE Focus software to determine the correct pin points for your application. - Page 15 Assembly Instructions SFV20 Figure 4.5.3 - VERA LA900 load adapter at pin point 11,5 - facing forward Moving the quick-locking pin of the VERA LA900 load adapter from 12 to 11 results in 11,5 as the new pin point. Figure 4.5.4 - VERA LA900 load adapter at pin point 13 - facing rearward For the rearward facing VERA LA900 load adapter , inserting quick-locking pins into 13 and 12 will result in 13 as the pin point.
-
Page 16: Mounting The Vera20 Loudspeaker
1. Please note that setting up the SFV rigging frame always requires two persons! WARNING 2. Place the SFV20 rigging frame on the top VERA20 loudspeaker. 3. Pull back the SFV20 rigging frame until its front splay links align with the rigging tracks of NOTE the top loudspeaker. - Page 17 8. Loosen the quick-locking pin on the main carrier of the upper VERA20 loudspeaker´s rear rigging. 9. Lower the SFV20 rigging frame until the hook slides into the main carrier of the rear rig- ging. 10. Insert the quick-locking pin into the main carrier of the top VERA20 loudspeaker´s rear rigging so that the rigging frame´s hook is connected to the top loudspeaker.
- Page 18 Assembly Instructions SFV20 13. Insert the hook of your chain hoist into the shackle of the VERA LA900 load adapter, which is mounted on the SFV20 rigging frame. The pin points suitable for your application have been previously selected. WARNING 14.
- Page 19 Assembly Instructions SFV20 17. Actuate the chain hoist and raise the SFV20 rigging frame with the VERA20 loudspeakers approximately one meter, moving each hook on the main carrier rear rigging to its holding position. WARNING 18. Move all left-hand sliders on all speakers to the right until they display the same angle value as the right-hand sliders.
- Page 20 Assembly Instructions SFV20 19. Actuate the chain hoist and raise the SFV20 rigging frame with the VERA20 loudspeakers once more. NOTE 20. Hold the lower part of the transport dolly with one hand. 21. Remove both quick-locking pins on the left and right side of the transport dolly and place it on the ground.
-
Page 21: Vera20 Setup From The Second Speaker Set
VERA20 setup from the second speaker set Continue setup of the VERA20 loudspeaker system for rigging as follows: 1. Please note that setting up the SFV20 rigging frame always requires two persons! WARNING 2. Proceed preparation for the second loudspeaker set as described in chapter 4.4. - Page 22 Assembly Instructions SFV20 5. Now fasten the two front quick-locking pins of the VERA20 loudspeaker in the holes of the top loudspeaker of the second speaker set. 6. Check that all quick-locking pins are always completely inserted! WARNING Figure 4.7.2 - Set quick-locking pins...
- Page 23 Assembly Instructions SFV20 7. Fold the hook, on the main carrier of the rear rigging, of the lowest speaker of the first loudspeaker set, completely down. NOTE 8. Loosen the quick-locking pin on the main carrier of the rear rigging of the top loudspeaker in the second loudspeaker set.
- Page 24 Assembly Instructions SFV20 9. Actuate the chain hoist and raise the SFV20 rigging frame with the VERA20 loudspeakers so that the loudspeakers lift off the ground and hang freely. WARNING Figure 4.7.4 - Second loudspeaker set...
- Page 25 Assembly Instructions SFV20 10. Move all left-hand sliders on all loudspeakers to the right until they display the same angle value as the right-hand sliders. Only the top speaker in the second speaker set is exempt from this step. Now all speakers in the lower set are securely mounted.
- Page 26 Assembly Instructions SFV20 11. Have two persons lift the second loudspeaker set until the hook of the bottom speaker of the first loudspeaker set meets the rear rigging of the top speaker of the second loudspe- aker set. WARNING 12. Insert the quick-locking pin on the main carrier of the rear rigging of the top loudspeaker in the second VERA20 loudspeaker set so that the hook is fixed.
- Page 27 Assembly Instructions SFV20 15. Actuate the chain hoist and raise the SFV20 rigging frame with the VERA20 loudspeakers once more. NOTE 16. Hold the lower part of the transport dolly with one hand. 17. Remove both quick-locking pins on the left and right side of the transport dolly and place it on the ground.
- Page 28 Assembly Instructions SFV20 19. Push the splay links on both sides back into the flying tracks and secure them using the quick-locking pins. NOTE Figure 4.7.8 - Set quick-locking pins...
-
Page 29: Compression Mode
Assembly Instructions SFV20 Compression mode The SFV20 rigging frame can be used for Compression mode. NOTE SFV20 Figure 4.8 - Compression mode... -
Page 30: Transport And Storage
This is why the product should be transported and stored in a safe, careful, dry and largely dust-free manner. The following accessories are available from TW AUDiO for the SFV20 rigging frame: • VERA LA900 (Load adapter incl. shackle) The original packaging is unsuitable as permanent storage and transport packaging. -
Page 31: Ce Declaration Of Conformity
Assembly Instructions SFV20 6. CE Declaration of Conformity Copy and translation of the original CE Conformity Declaration: We hereby declare that the below-referenced components by virtue of their design and con- struction, and in the configuration placed on the market by us, satisfy the safety and health requirements of the applicable EC directives. - Page 32 Assembly Instructions SFV20 TWAMBO GmbH Karl-Hofer-Str. 42 14163 Berlin Germany Phone: + 49 (0) 71 41-48 89 89 0 Fax: + 49 (0) 71 41-48 89 89 99 E-Mail: info@twaudio.de WWW: www.twaudio.de...
Need help?
Do you have a question about the SFV20 and is the answer not in the manual?
Questions and answers