Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for twaudio VERA ORF900
Summary of Contents for twaudio VERA ORF900
- Page 1 Assembly VERA ORF900 Instructions...
- Page 2 Introduction Thank you for choosing a high-quality product “MADE IN GERMANY” from TW AUDiO. The VERA ORF900 outrigger is an accessory for the VERA RF600 and VERA RF900 rigging frames. It is characterized by a subtle look, a remarkable size to weight ratio and ease of use.
- Page 3 Assembly Instructions VERA ORF900 Notes on the products Before using the outrigger, carefully read the assembly instructions and keep the instructions Read manual in a safe place together with the VERA ORF900 outrigger. before use! General Information Assembly Guide: OM -VERA ORF900 Version 1.0 d, 12/2018...
-
Page 4: Table Of Contents
1. Safety | Intended use ...................... 5 2. Overview ........................6 Scope of delivery ..................... 6 Placement the VERA ORF900 for storage on the VERA RF600 or VERA RF900 ..7 3. Technical specifications ....................8 Data sheet ....................... 8 4. -
Page 5: Safety | Intended Use
The VERA ORF900 outrigger set may only be used by trained and qualified personnel. Personnel must check the VERA ORF900 for its full suitability before each use. WARNING When visible damage to any part of the VERA ORF900 outrigger set is detected, it must be decommissioned immediately. WARNING... -
Page 6: Overview
2. Overview Scope of delivery The VERA ORF900 consists of four outrigger with spindle feet and quick-lock pins. Screw all spindle feet of the outrigger set VERA ORF900 to the specified dimension which is shown at figure 2.1. NOTE Figure 2.1 - VERA ORF900 Outrigger... -
Page 7: Placement The Vera Orf900 For Storage On The Vera Rf600 Or Vera Rf900
Rigging frame VERA RF900 Outrigger VERA ORF900 For storage, first insert all quick-lock pins through the mounting holes of the VERA ORF900 out- rigger set and then through the mounting holes on the VERA RF600 or VERA RF900 rigging frame. -
Page 8: Technical Specifications
Data sheet Weight 5,0 kg (11,023 lbs) Surface Powder coated 4. Commissioning Setup The VERA ORF900 Outrigger is designed for groundstack operation. TW AUDiO recommends using only the accessories specified by TW AUDiO for securing and mounting the outrigger. NOTE... -
Page 9: Assembly Rear: Vera Orf900 Outrigger Attached To Vera Rf600 Rigging Frame
Assembly Instructions VERA ORF900 4.2 Assembly rear: VERA ORF900 outrigger attached to VERA RF600 rigging frame 1. Insert the first outrigger into the square tube on the VERA RF600 rigging frame at the rear left position. Attach the outrigger to the rigging frame by means of a quick-lock pin. If possible, use the outermost mounting hole A on the outrigger. -
Page 10: Assembly Rear: Vera Orf900 Outrigger Attached To Vera Rf900 Rigging Frame
Assembly Instructions VERA ORF900 4.3 Assembly rear: VERA ORF900 outrigger attached to VERA RF900 rigging frame 1. Insert the first outrigger into the square tube on the VERA RF900 rigging frame at the rear left position. Attach the outrigger to the rigging frame by means of a quick-lock pin. If pos- sible, use the outermost mounting hole A on the outrigger. -
Page 11: Assembly Front: Vera Orf900 Outrigger Attached To Vera Rf600 Rigging Frame
Assembly Instructions VERA ORF900 4.4 Assembly front: VERA ORF900 outrigger attached to VERA RF600 rigging frame 1. Insert the third outrigger into the square tube on the VERA RF600 rigging frame at the front left position. Attach the outrigger to the rigging frame by means of a quick-lock pin. If possible, use the outermost mounting hole A on the outrigger. -
Page 12: Assembly Front: Vera Orf900 Outrigger Attached To Vera Rf900 Rigging Frame
Assembly Instructions VERA ORF900 4.5 Assembly front: VERA ORF900 outrigger attached to VERA RF900 rigging frame 1. Insert the third outrigger into the square tube on the VERA RF900 rigging frame at the front left position. Attach the outrigger to the rigging frame by means of a quick-lock pin. If pos- sible, use the outermost mounting hole A on the outrigger. -
Page 13: Ground
Assembly Instructions VERA ORF900 Ground 1. When setting up a system on uneven surfaces, such as gravel or grass, always put a pres- sure-resistant surface under all four spindle feet! 2. Make sure that all four spindle feet rest completely on the pressure-resistant shims and WARNING that the surface can withstand the total weight. -
Page 14: Alignment
Assembly Instructions VERA ORF900 Alignment Always level the VERA RF600 or VERA RF900 rigging frame using a spirit level before com- mencing system construction. To do so, turn the spindle feet. Make sure that the VERA RF600 or VERA RF900 rigging frame rests completely on the spindle WARNING feet. -
Page 15: Pitfalls
Assembly Instructions VERA ORF900 Pitfalls Make sure that no one can trip over your system structures, or over individual components! This is especially true for all pressure-resistant shims and spindle feet! WARNING Danger of tipping over For each downtilt system structure, make sure that the center of gravity never exceeds the... -
Page 16: Transport And Storage
Assembly Instructions VERA ORF900 5. Transport and Storage Ensure that the surface of the outrigger is not damaged during transport and storage. Moisture may penetrate where steel surfaces are exposed by scratches and result in corrosion. NOTE This is why the product should be transported and stored in a safe, careful, dry and largely dust-free manner. -
Page 17: Ce Declaration Of Conformity
Assembly Instructions VERA ORF900 6. CE Declaration of Conformity Copy and translation of the original CE Conformity Declaration: We hereby declare that the below-referenced components by virtue of their design and con- struction, and in the configuration placed on the market by us, satisfy the safety and health requirements of the applicable EC directives. - Page 18 Assembly Instructions VERA ORF900 TW AUDiO GmbH Osterholzallee 140 71636 Ludwigsburg Germany Telefon: + 49 (0) 71 41-48 89 89 0 Telefax: + 49 (0) 71 41-48 89 89 99 E-Mail: info@twaudio.de WWW: www.twaudio.de...
Need help?
Do you have a question about the VERA ORF900 and is the answer not in the manual?
Questions and answers