All information and notes in these operating instructions You have made a good choice by purchasing the were summarised while taking applicable standards CLEANCRAFT vacuum cleaner and rules, the state-of-the-art technology and our long- term knowledge and experiences into consideration.
Safety Obligations of the operating company CAUTION! If the vacuum cleaner is used for commercial purposes, This combination of symbol and signal words indi- the operating company of the vacuum cleaner must cates a potentially dangerous situation which may comply with the legal working safety regulations. There- lead to slight or minor injury if not avoided.
Safety 2.3 Requirements to staff 2.4 Personal protective equipment Qualifications The personal protective equipment serves to protect persons against impairments of safety and health while The different tasks described in this manual represent working. The staff member has to wear personal protec- different requirements to the qualification of the persons tive equipment while performing different tasks on and entrusted with these tasks.
Intended use - The vacuum cleaner must not be used for the suc- tion of water, oil or other liquids. ATTENTION! - Do not use the device at an altitude of 2000 m When the device fall over,it is then recommended above sea level.
Technical Data use or any other use is regarded as misuse. Under no 3.2 Residual risks circumstances may personnel be lifted. Stürmer Maschinen GmbH accepts no liability for any Even if all safety instructions are observed, and the ma- constructional or technical modifications carried out on chine is put to its intended use, there are still residual the electric vacuum cleaner.
Transport, packaging, storage 4.1 Type plate Description of the device Fig. 2: Type plate flexCAT 112 Q Transport, packaging, storage 5.1 Transport Check the vacuum cleaner on delivery for any visible transportation damage. If you notice any damage to the device please report this immediately to the carrier or dealer.
Page 9
Description of the device Fig. 3: Description of the device A - Motor head B - Switch C - Cable holder D - Exhaust air grid E - Hooks F - Tank G - “T” slot H - Inlet I - Castor wheels Fig.
Description of the device Detachable cable Assembly of the main filter The vacuum cleaner flexCAT 116 Q is equipped with a Step 1: Loosen the side hooks and remove the upper part detachable cable. With the help of this function can de- of the container.
Page 11
Description of the device Fig. 12: Assembly of the tool holder (optional) Storage options on the Special Vacuum Cleaner The vacuum cleaner offers the possibility of placing the tube on top of the container (Fig. 13 top left). The correct storage of the power cable is the wound state at the top of the container (Fig.
Scope of delivery Scope of delivery The Special Vacuum Cleaner flexCAT 112 Q will be deli- vered with (Fig.14): Item number: Designation: 7010360 Polyester filter 850 cm² (Pos. 2) 7010361 Filter bag 11 l (Pos. 6) 7010362 Exhaust air filter (Pos. 4) 7010363 Hose 2 m Ø...
Operation Accessories for the flexCAT 116 Q (Fig. 17): ATTENTION! Item number: Designation: To maintain the performance of the system, it is 7010386 Paper filter bag (1) recommended clean the filter after each use and 7010302 Poly-cartridge filter (2) clean or replace the filter bag. 7010303 HEPA-cartridge filter (3) 7010362...
Care, maintenance and repair Keep the ventilation slots of the engine clean to ensure 8.1 Start and stopping adequate cooling. Start - Insert the power plug into a suitable power socket ATTENTION! - Press the ON/OFF switch. Always empty the tank and clean all parts of the Stopping vacuum cleaner after the vacuuming.
If you can not eliminate the problems with your va- materials by the disposal channels provided. cuum cleaner yourself, then please contact your CLEANCRAFT dealer. Please mark down the follo- 10.2 Waste disposal of electric equipment wing information from the vacuum cleaner or instruc- tion manual, this will help you best with your problem.
Spare parts 12 Spare parts Example A covering for the vacuum cleaner flexCAT 112 Q must be ordered. The covering ist identifies in the spare parts DANGER! drawing with the position number 2. Danger of injury by the use of wrong spare When ordering spare parts, send a copy of the spare parts! Dangers may result for the user and damages as...
Spare parts 12.2 Spare parts drawings In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Spare parts drawings flexCAT 112 Q Fig.
Page 18
Spare parts Fig. 19: Spare parts drawing 2, main filter flexCAT 112 Q Fig. 20: Spare parts drawing 3, base frame, flexCAT 112 Q flexCAT-Series | Version 1.04...
Page 19
Spare parts Spare parts drawings flexCAT 116 Q Fig. 21: Spare parts drawing 1, head, flexCAT 116 Q flexCAT-Series | Version 1.04...
Page 20
Spare parts Fig. 22: Spare parts drawing 2, main filter, flexCAT 116 Q Fig. 23: Spare parts drawing 3, base frame, flexCAT 116 Q flexCAT-Series | Version 1.04...
According to Machinery Directive 2006/42/EC, Annex II 1.A Stürmer Maschinen GmbH Manufacturer / distributor: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt hereby declares that the following product Cleancraft® Sauggeräte Product group: Special Vacuum Cleaner Type of machine: Designation of the machine*: Item number:...
Need help?
Do you have a question about the flexCAT Series and is the answer not in the manual?
Questions and answers