Remote Controller - homelabs HME020379N Instructions Manual

Remote Controller

SPECIFICATIONS & FUNCTION BUTTONS
Applied Model:
Rated Voltage:
Signal Receiving Range:
Operating Environment:
Before you begin using your new Air Conditioner, make sure to familiarize yourself with its Remote Controller. For instructions on how
to operate your Air Conditioner, refer to the How to Use Basic Functions section of this manual
On/Off
Turns the unit on or off.
Mode
Scrolls through
operation modes
as follows:
AUTO → COOL → DRY → FAN
Fan Speed
Selects fan speeds in the
following order:
AUTO → LOW → HIGH
Sleep
Can save energy during
sleeping hours.
Swing
Starts and stops Air Outlet door
movement.
NOTE:
See Page > 23 for Remote Controller LED Screen details.
NOTE:
Button designs on your unit may differ from the example shown. If the unit
does not have a particular function, pressing that function button on the
Remote Controller will have no effect. When there are differences between
the Remote Controller illustration Remote Controller illustration and the USER MANUAL on function
description, the description on the USER MANUAL should prevail.
HME020379N, HME020235N
3.0 V (Dry batteries R03/LR03 × 2)
26 ft (8 m)
23°F~140°F (-5°C~60°C)
(See Page > 24).
Temp
Increases temperature in 1°F (1°C) increments.
Max 86°F (30°C).
Temp
Decreases temperature in 1°F (1°C) increments.
Min 62°F (17°C).
Shortcut
Sets and activates your
favorite pre-settings.
Timer On
Sets a time to turn the unit on.
(See Page > 26 for details).
Timer Off
Sets a time to turn the unit off.
(See Page > 26 for details).
LED
Turns LED display on and off.
If you are sensitive to light when
you go to sleep, you can press
the LED button to turn off the
LED display. Press the button
again to turn it on.
22
Remote Controller
HANDLING THE REMOTE CONTROLLER
Inserting and Replacing Batteries
Your Remote Controller comes with two AAA batteries. Put the batteries in the Remote Controller before use:
1. Slide the back cover from the Remote Controller downward to open the battery compartment.
2. Insert the batteries. Be careful to match the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back to close.
Battery Notes
For optimum performance and safety, do not mix old and new batteries, or batteries of different types. Do not leave batteries in the
Remote Controller if you don't plan on using the device for more than 2 months.
Battery Diposal
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.
Tips for Using Remote Controller
• The Remote Controller must be used within 26.2 ft (8 meters) of the unit.
• The unit will beep when the remote signal is received.
• Curtains and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries when the Remote Controller is not intended to be used for 2 months.
REMOTE CONTROLLER LED SCREEN
Transmission Indicator
Lights up when sending
signal to the unit.
On/Off Display
Appears when the unit is turned
on, and disappears when it is
turned off.
Mode Display
Displays the current
mode, including:
Timer On Display
AUTO
Displays when
" Timer On " is activated.
COOL
DRY
FAN
Fan Speed Display Temperature/Timer Display
Displays selected fan speed: Displays the set temperature by default, or "Timer" setting when
"High" or "Low" using "Timer On/Off" functions.
The display is blank when
Temperature range: 62
on "Auto".
"Timer" setting range: 0–24 hours
The display is blank when operating in "Fan" mode.
Timer Off Display
Displays when
" Timer Off is " activated.
Battery Display
Low battery
detection.
Sleep Display
Displays when
" Sleep " funtion
is activated.
° F–86OF (17–30 ° C)
23