SWR WorkingPro WorkingPro 700 User Manual page 9

Workingpro series bass amplifiers

Hide thumbs Also See for WorkingPro WorkingPro 700:

Owner's manual (10 pages)

Service manual (21 pages)

Owner's manual (44 pages)

page of 10

/ 10
Bookmarks

To preserve the beauty and reliability of your amplifier, we

recommend that you install your amplifier in a rack case.

The WorkingPro™ is completely ready to be rack mounted

and needs no additional parts or accessories other than

the rack screws and the case itself.

The WorkingPro™ takes up two full rack spaces (3 1/2").

If the rack in which you mount your WorkingPro™ requires

that the rubber feet on the bottom of the chassis be

removed, please remember to keep the screws handy in

case you wish to reattach the rubber feet at a later date.

The WorkingPro™ should be mounted as close to the

bottom of the rack case as possible. If you must mount

the WorkingPro™ in an area of the rack other than the

bottom space, a piece of wood or similar solid material

should be installed between the bottom of the rack case

and the bottom of the amplifier to prevent flexing of the

MODEL:

PART NUMBERS:

POWER REQUIREMENT:

POWER AMP

MINIMUM IMPEDANCE:

POWER OUTPUT:

PRE AMP

INPUT IMPEDANCE:

SENSITIVITY AT FULL POWER:

TONE CONTROLS

MIDRANGE SEMI-PARAMETRIC EQ:

BASS INTENSIFIER:

TRANSPARENCY:

EFFECTS LOOP

SEND IMPEDANCE:

RETURN IMPEDANCE:

UNBALANCED LINE OUT SEND IMPEDANCE:

BALANCED LINE OUT

SEND IMPEDANCE:

FOOTSWITCH (INCLUDED):

LINE FUSE

110V-120V MODELS:

230V-240V MODELS:

DIMENSIONS

WEIGHT:

WorkingPro™ 400

4450200010 (120V, 60Hz) USA

4450203010 (240V, 50Hz) AUS

4450204010 (230V, 50Hz) UK

4450206010 (230V, 50Hz) EUR

4450207010 (100V, 50Hz) JPN

840 W

SENSITIVITY:

700mV RMS, 1kHz

400W RMS into 4 @ < 0.1% THD, 1kHz

250W RMS into 8 @ < 0.1% THD, 1kHz

3.9M

15mV

BASS:

±15dB @ 100Hz

TREBLE:

±15dB @ 2kHz

±15dB @ MID FREQ frequency

±15dB below CUTOFF freq

±15dB @ 5kHz

27k

1.5k

2-button, Mute, Bass Intensifier (P/N 065436)

T8A, 250V

T4A, 250V

HEIGHT:

3.5 in (8.9 cm)

WIDTH:

19 in (48.3 cm)

DEPTH:

13.5 in (34.3 cm)

25 lb (11.25 kg)

Product specifications are subject to change without notice.

s s w

w r r s s o

amplifier's chassis. Severe or constant flexing of the

chassis can damage the amplifier and is not covered

under the warranty.

Please do not forget about your amp after it has been

installed in a rack case. Continuous transportation and

vibration can cause screws to become loose, both on the

WorkingPro™ and with your rack case rails. We

recommend that at least once a month you remove the

WorkingPro™ from the case and tighten all outside screws

and wipe off the outside of the chassis with a damp cloth.

Then check all the connections in your rack case and

reinstall the unit.

o u

u n

n d

d . . c

c o

o m

R R

a a

c c

k k

M M

o o

u u

n n

t t

R R

a a

c c

k k

M M

o o

u u

n n

t t

S S

p p

e e

c c

i i

f f

i i

c c

a a

t t

i i

o o

S S

p p

e e

c c

i i

f f

i i

c c

a a

t t

i i

WorkingPro™ 700

4450000010 (120V, 60Hz) USA

4450003010 (240V, 50Hz) AUS

4450004010 (230V, 50Hz) UK

4450006010 (230V, 50Hz) EUR

4450007010 (100V, 50Hz) JPN

1440 W

1V RMS, 1kHz

700W RMS into 4 @ < 0.1% THD, 1kHz

440W RMS into 8 @ < 0.1% THD, 1kHz