Cleaning the detergent dispenser Caring for your appliance door and drum Cleaning the pump Checking the water inlet hose Precautions and advice, 9 WDI 651 WH General safety Disposal Saving energy and respecting the environment Washer-dryer description, 10-11 Control panel...
Installation ! Keep this instruction manual in a safe place for Levelling your appliance correctly will provide future reference. Should the appliance be sold, tran- it with stability and avoid any vibrations, noise sferred or moved, make sure the instruction manual and shifting during operation.
Page 3
Connecting the drain hose • the supply voltage is included within the va- lues indicated on the Technical details table ; Connect the drain hose, without ben- • the socket is compatible with the washing ding it, to a draining machine’s plug.
As the colours of the wires in the lead may ! The power supply cable must only be repla- not correspond with the coloured markings ced by an authorised serviceman. identifying the terminals in your plug, proceed as follows: Warning! The company denies all liability if Connect Green &...
Page 5
Technical data Model WDI 651 WH width 59.5 cm Dimensions height 81.5 cm depth 54.5 cm from 1 to 6 kg for the wash Capacity programme; from 1 to 5 kg for the drying programme please refer to the technical...
Instructions for the fitter Door Mounting Accessories (Fig. 1-2-3-4-5). Mounting the wooden panel onto the door and inserting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its ori- ginal packaging.
Page 7
Using the Drilling Template. - To trace the positions of the holes on the left- hand side of the panel, align the drilling tem- plate to the top left side of the panel using the lines traced on the extremities as a reference. - To trace the positions of the holes on the right-hand side of the panel, align the drilling template to the top right side of the panel.
Care and maintenance Cutting off the water or electricity 2. clean the interior thoroughly; supply 3. screw the lid back on. Checking the water inlet hose • Turn off the water tap after every wash. This will limit the wear of your appliance’s water Check the water inlet hose at least once a year.
If you only see a little water through your appliance door, softener instructions. this is because thanks to the latest Nordmende tech- – The final part of a tumble dryer cycle occurs nology, your washing machine only needs less than half...
Washer-dryer description FUNCTION Control panel ON-OFF/DOOR Buttons LOCK Leds ON-OFF Button Detergent dispenser DRYING START/RESET Knob Button TEMPERATURE Knob Detergent dispenser: to add detergent and fabric ON-OFF/DOOR LOCK Led: to find out whether the softener. Washer-dryer is on and if the appliance door can be opened.
Leds Cycle phase under way: During the wash cycle, the LEDs gradually illuminate on to indicate the cycle phase under way: The LEDS provide important information. This is what they can tell you: Prewash / Wash Delay set: Rinse If the Delay Timer function has been enabled, once you have started the programme, the LED corresponding to Spin cycle the delay set will begin to flash:...
Starting and Programmes Briefly: starting a programme 6. Add the detergent and any fabric softener. 7. Start he programme by pressing the START/RESET but- 1. Switch the Washer-dryer on by pressing button . All ton. To cancel it, keep the START/RESET button pressed the LEDS will light up for a few seconds and the ON-OFF/ for at least 2 seconds.
Personalisations Setting the temperature Turn the TEMPERATURE knob to set the wash temperature. The temperature can be lowered, or even set to a cold wash ( ). Set the drying cycle Turn the DRYING knob to set the desired drying type. Two options are available: A - Based on time: From 40 minutes to 180.
Detergents and laundry Detergent dispenser Good washing results also depend on the correct dose of detergent: adding too much detergent won’t necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment.
Troubleshooting Your Washer-dryer could fail to work. Before calling for Assistance, make sure the problem can’t easily be solved by consul- ting the following list. Possible causes/Solution: Problem The machine does not switch on. • The appliance is not plugged into the socket fully, or not enough to make contact.
Page 16
The machine is noisy. • There will always be some motor, pump and drum noise during spin. The machine wont spin properly. • Out of Balance detected when attempting to go into a spin cycle - If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly.
Service Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate.