Table of Contents
Advertisement
PV-D300 / VM-D100 / PV-L550 / PV-L600 / PV-L650 / VM-L450
Copying your Tapes (dubbing)
Connections
Source (Playing)
Camcorder
Audio/Video
Out
VHF Connecting
Cable (not supplied)
Recording:
VCR
To Audio
To Video
In
In
Audio/Video Cable
(supplied)
Monitor with your TV
• Turn TV on and tune to VCR
channel (CH3 or CH4).
• Set TV/VCR Selector on VCR to VCR.
Focus
Auto Focus
(PV-L650 shown)
Manual Focus
Use Manual Focus (MF) when :
• recording through glass.
• lighting is poor.
• subject is far away with objects in foreground.
• subject has distinct horizontal lines.
(PV-L650 shown)
1
,
2
4
Macro Focus (close-ups)
Auto Focus functions up to 12.7 mm (1/2 inch) from subject.
Hold down "W" on POWER ZOOM to maximum wide angle.
Bring Camcorder up close to the subject.
Before you begin...
• Make Camcorder-VCR connections
(see left).
STILL
• Turn both units on.
• Set VCR input signal to LINE.
Please see VCR owner's manual.
PLAY
• Set Camcorder POWER to VCR.
REW
FF
1
STOP
Insert a pre-recorded tape
into Camcorder and a blank tape with
record tab into VCR.
2
Press PLAY on Camcorder, then
press STILL at starting point.
3
Press REC, then STILL/PAUSE on
VCR.
TV
4
Press STILL on Camcorder and
STILL/PAUSE on VCR again to start
copying.
5
Press STOP on both units to stop
copying.
Note:
• Camcorder will only playback tapes
recorded in SP or SLP mode.
• Dubbing may reduce picture quality.
CAUTION:
Unauthorized exchanging and/or
copying of copyrighted recordings may
be copyright infringement.
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
Camcorder automatically focuses on
subject even during zooming.
Auto Focus is on when "MF" is not
displayed in EVF or LCD monitor. Push
MANUAL FOCUS to remove "MF" in EVF
MANUAL
FOCUS
or LCD monitor if necessary.
• subject is not centered in EVF or LCD monitor.
• subject has shiny surface.
• subject is slanted.
• subject is bright and flat, like a white wall.
• subject has fast motion, like a golf swing.
1
Push MANUAL FOCUS so "MF"
(Manual Focus) appears in EVF or
LCD monitor.
EVF or LCD Monitor
2
3
Hold down "T" (telephoto) on
POWER ZOOM to maximum zoom
in.
3
Turn MANUAL FOCUS until subject
is in focus.
• Back away from subject if necessary.
4
Hold down "W" (wide angle) on
POWER ZOOM as desired.
• Refocus as needed
when aiming at new scenes.
Power Zoom / Backlight
Four-Speed Power Zoom
Zoom in (close up) and out (wide angle)
in one of four speeds ranging from slow
(16 seconds) to fast (2 seconds).
T
W
Backlight
Use when subject is darker than
surroundings, in shadowed area, or in front
of the light source.
BACKLIGHT
High Speed Shutter
Improves Still or Slow Motion playback
picture of high speed subjects (e.g. a tennis
stroke), when viewed on Camcorder or 3
or 4 head VCR.
Auto Shutter
In AUTO mode (no indication in EVF or LCD Monitor), shutter speed is auto-adjusted
from 1/60 to 1/350 according to subject brightness.
• AUTO mode is selected each time POWER is set to CAMERA.
Manual Selection
The faster the shutter speed, the more light is needed for proper picture and color quality.
High Speed Shutter indication flashes if light is inadequate. Provide additional light.
H.S.SHUTTER TITLE
MF
HIGH SPEED
SHUTTER
No Indication
1/60
EVF or LCD Monitor
1/100
1/250
1/500
1/1000
1/2000
1/4000
1/10000
8
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
Zoom In ("T")
2
8
X
X
Zoom Out ("W")
Zoom slowly:
Lightly press "T" (telephoto) or "W" (wide
angle) POWER ZOOM button.
Zoom quickly:
Apply more pressure to the button.
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
Press BACKLIGHT while recording to
select the level of backlight compensation.
In normal lighting, press BACKLIGHT
repeatedly until no indicator displayed.
EVF or LCD Monitor
Normal (no display)
First press
(low)
Second press
(medium)
Third press
(high)
Fourth press
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
• Insert cassette with record tab.
1
Press HIGH SPEED SHUTTER
while recording.
2
Press repeatedly to change shutter
speed.
(See below, left.)
Note:
• Provide additional halogen or tungsten
light for use indoors or in poor light.
Fluorescent light degrades picture.
• Auto Focus may not function properly if
high speed shutter is used in inadequate
light.
• Setting reverts to AUTO each time
POWER is set to CAMERA.
Advertisement
Table of Contents
