Panasonic Quasar PV-D300 Service Manual page 4

PV-D300 / VM-D100 / PV-L550 / PV-L600 / PV-L650 / VM-L450
Camera Recording
(PV-L550/PV-L600/PV-L650/VM-L450)
Using the LCD Monitor
View recording scene on the LCD (Liquid
Crystal Display) monitor.
4
2
(PV-L650 shown)
1
REC
5
VCR CAMERA
OFF
Camera Recording (continued)
Easy Edit Stand-by
For a smooth transition between scenes if
recording is stopped, and then started within
24 hours.
REC REC
VCR
OFF
1 4
,
2
Manual Easy Editing
For proper continuity when taping from Stop
mode or after attaching a new Battery.
STILL
C
PLAY
B
REW FF
A
STOP
REC REC
2
VCR
OFF
4
1
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab.
1
Press LCD-OPEN to unlock LCD
monitor.
2
Swing LCD monitor fully open and
adjust viewing angle.
Caution:
Rotating partially open LCD monitor
may block cassette door and damage
Camcorder body.
3
Set POWER to CAMERA.
• LCD monitor turns on/off by the
POWER switch.
• EVF shuts off when LCD monitor is
opened and turns back on when
LCD is closed.
• Both EVF and LCD monitor turn on
when LCD is at 180 (see above
left).
This allows both you and the subject
3
to view the recording.
4
Turn BRIGHT control to adjust LCD
monitor brightness level.
5
Press RECORD/PAUSE to start
recording.
Note:
• Using LCD monitor reduces battery operation
time.
• Return LCD monitor to locked position when not
in use.
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab.
1
Press RECORD/PAUSE to stop
recording.
2
Set POWER to OFF and leave
cassette in Camcorder.
3
To resume recording, set POWER
to CAMERA.
4
Press RECORD/PAUSE to resume
recording.
CAMERA
Note:
• Use Manual Easy Edit (below) if more than
24 hours before recording is resumed.
3
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab.
1
Set POWER to VCR.
2
A Press REWIND/SEARCH to
rewind a few seconds of tape.
B
Press PLAY to review recording.
C
Press STILL where you want to
continue recording.
3
Set POWER to CAMERA.
4
Press RECORD/PAUSE to resume
recording.
CAMERA
3
Stand-by Quick Release
If left in RECORD/PAUSE mode for 5 minutes, Camcorder switches to Stand-by mode to
conserve battery. When set to ON, Stand-by Quick Release lets you resume recording by
pressing RECORD/PAUSE two times. New camcorders will default to OFF.
REC
VCR CAMERA
OFF
RECORD/
PAUSE
UP
DOWN
2 3
,
MENU
DISPLAY
Programmed Recording
Set a recording start and stop time. Or, set
a 5 or 10 second interval recording to be
done each minute.
UP
DOWN
1 2 3
, ,
MENU
DISPLAY
4
10MIN. 20MIN. 30MIN. TO TAPE END
* 2
INTERVAL INTERVAL
10 SEC/MIN. 5 SEC/MIN.
*1 Interval 5 SEC/MIN:
Record 5 seconds each minute.
*2 Interval 10 SEC/MIN:
Record 10 seconds each minute.
Note:
• Start time may not be set over 24 hours
from current time.
• Camcorder shuts off at tape end, or 12
hours after Interval Recording starts.
• To cancel, set POWER to OFF.
6
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab.
1
Set POWER to CAMERA.
2
Press MENU for MENU mode.
Press UP or DOWN to select
STAND-BY RELEASE .
- - - MENU - - - PAGE 1/2
1
PROGRAMMED REC PROGRAMMED REC
TITLE ; AUTO/MANUAL ; AUTO/MANUAL
TALLY LAMP TALLY LAMP ; ON ; ON
STAND-BY RELEASE ; OFF ; OFF
CLOCK SET CLOCK SET
SELECT : PUSH SELECT : PUSH / / KEY KEY
SET SET : PUSH DISPLAY KEY : PUSH DISPLAY KEY
END END : PUSH MENU KEY : PUSH MENU KEY
3
Press DISPLAY to select ON/OFF.
4
,
ON: From Stand-by mode,
press RECORD/PAUSE two times
to resume recording.
OFF: From Stand-by mode,
set POWER to OFF, then to
CAMERA.
Press RECORD/PAUSE to record.
4
Press MENU to exit.
Before you begin...
• Connect Camcorder to power source.
Use AC Adaptor for longer recordings.
• Insert cassette with record tab.
• Set POWER to CAMERA.
1
Press MENU for MENU mode.
Press UP or DOWN to select
PROGRAMMED
- - - MENU - - - - - - MENU - - - PAGE 1/2 PAGE 1/2
REC .
PROGRAMMED REC PROGRAMMED REC
TITLE TITLE ; AUTO/MANUAL ; AUTO/MANUAL
TALLY LAMP TALLY LAMP
STAND-BY RELEASE ; OFF STAND-BY RELEASE ; OFF
CLOCK SET CLOCK SET
SELECT : PUSH SELECT : PUSH / / KEY KEY
SET SET : PUSH DISPLAY KEY : PUSH DISPLAY KEY
END END : PUSH MENU KEY : PUSH MENU KEY
2
Press DISPLAY. (Current time is
displayed.)
Each additional press of DISPLAY
increases start
time by 30
START START ; ; 10 : 20PM 10 : 20PM
minutes.
REC TIME REC TIME ; 10MIN. ; 10MIN.
SELECT : PUSH SELECT : PUSH / / KEY KEY
SET SET : PUSH DISPLAY KEY : PUSH DISPLAY KEY
START : PUSH RECORD KEY START : PUSH RECORD KEY
CANCEL: PUSH MENU KEY CANCEL: PUSH MENU KEY
10:20:00 10:20:00PM PM
3
Press DOWN to select REC
TIME . Press DISPLAY repeatedly to
select one of the options shown at
the left.
* 1
START ; START ; 10 : 20PM 10 : 20PM
REC TIME ; 10MIN. ; 10MIN.
SELECT : PUSH SELECT : PUSH / / KEY KEY
SET SET : PUSH DISPLAY KEY : PUSH DISPLAY KEY
START : PUSH RECORD KEY START : PUSH RECORD KEY
CANCEL: PUSH MENU KEY CANCEL: PUSH MENU KEY
10:20:00PM 10:20:00
To cancel the setup, press MENU
twice.
4
Press RECORD/PAUSE to place
Camcorder in stand-by mode.
STAND-BY
START ; START ; 10:20PM
REC TIME ; 10MIN. REC TIME ; 10MIN.
10:20:00 10:20:00PM PM
JUN JUN 1 2000 1 2000
Recording will be done as scheduled.
; ON ; ON