SMC Networks Barricade SMCWBR14-G Quick Installation Manual

EZ Installation CD

Troubleshooting

After unpacking the SMC WBR14-G, check the contents of the box to be sure

Wireless Networking

you have received the following components:
• One Barricade™ g Wireless Broadband Router
• One Power Adaptor
• One Ethernet Cable

Initial Configuration

• One CD-ROM
Immediately inform your dealer in the event of any incorrect, missing or
damaged parts. If possible, please retain the carton and original packing
materials in case there is a need to return the product.
Please register this product and upgrade the product warranty at SMC's Web
site: http://www.smc.com
To install and connect to the SMCWBR14-G, you must have:
• An external Cable or DSL modem with an Ethernet port
• An account with an ISP for Cable or DSL access
• A Computer with a CD-ROM drive and working Ethernet port
• Windows (98 or later), MacOS (9.x or later) or Linux
• An up to date web browser:
• Internet Explorer 5.5 or later
Mozilla 1.7/Firefox 1.0 or later
NOTE: A CD-ROM drive required to read the manual and if you want to use the
EZ 3-Click Installation Wizard application to configure your Barricade Router.
The installation process can be completed manually through the web interface.
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of
patents or other rights of third parties, which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right
to change specifications at any time without notice.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
Copyright © SMC Networks, Inc., 2004. All rights reserved.
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc.
Other product and company names are trademarks or registered trademarks of their
respective holders.
FOR TECHNICAL SUPPORT, CALL: World Wide Web:
From U.S.A. and Canada http://www.smc.com/
(24 hours a day, 7 days a week)
(800) SMC-4-YOU; Phn: (949) 679-8000; If you are looking for further contact
Fax: (949) 679-1481 information, please visit www.smc.com.
From Europe : Contact details can be found
on www.smc.com
38 Tesla
Irvine, CA 92618
INTERNET
Phone: (949) 679-8000
E-mail addresses:
techsupport@smc.com
Model Number: SMCWBR14-G
european.techsupport@smc-europe.com
Driver updates:
http://www.smc.com/index.cfm?event=downloads.searchCriteria&localeCode=EN_USA
Using The EZ 3Click Wizard
Front
1. Power (PWR) LED
EZ Installation CD When this green LED is on, the router is powered up.
2.Wireless LAN (WLAN) LED
When this green LED is on, wireless networking is enabled. The LED will flash
when data is sent or received over a wireless connection.
Hardware Installation
3. WAN LEDs
When the top - green - LED is on, the router has a 100Mbps link to the WAN
(Wide Area Network).
When the bottom - amber - LED is on, the router has a 10Mbps link to the WAN.
Only one LED will be on at any one time; the LED will turn on when a connection is
made and will flash to indicate that data is being sent or received over the WAN link
(see 7).
EZ Installation CD
4.LAN LEDs (LAN1, LAN2, LAN3 and LAN4)
There are two LEDs - one above the other - for each LAN (Local Area Network) port
(see 5). The top LED is green and the bottom is amber. These two LEDs behave in
exactly the same way as the WAN LEDs.
Hardware Installation
Back
5.LAN Ports (LAN1, LAN2, LAN3 and LAN4)
There are four Ethernet LAN ports for connection to PCs, network printers or similar
devices. Note the labelling; one pair of LAN LEDs on the front panel is associated
with one port on the rear panel. If a device is not correctly connected, using a
suitable Ethernet cable, the associated LED will not turn on.
6.Reset
If, for any reason, you need to reset the unit to factory defaults and cannot access
the user interface (e.g. if you have changed and forgotten the password), press the
reset button for 10 seconds. Note that you will lose all your configuration changes.
7. WAN Port
Use the supplied Ethernet cable to connect the WAN port to your cable or DSL
modem. The associated LED on the front panel will light up when the connection is
made.
8.Power
Connect the supplied, 12V power adapter to this socket.
Ethernet Cables
One Ethernet cable, intended for your WAN connection, is bundled with the router. You
can use this as a point of reference for purchasing other cables; the cable is constructed
from unscreened, "Cat 5" cable with RJ45 connecters at both ends. Cables of this
type can be purchased at most computer retailers.
Barricade™g Wireless
4-Port Broadband Router
EZ Installation CD
Hardware Installation
Barricade™g Wireless
4-Port Broadband Router
SMCWBR14-G
SMCWBR14-G
SMC