Related Manuals for Felicitysolar HVC-BMU
Summary of Contents for Felicitysolar HVC-BMU
- Page 1 Make life full of hope User Manual LiFePO4 Battery System High voltage energy storageLithium battery pack 358-010299-00A...
-
Page 2: Table Of Contents
LiFePO4 Battery System Contents 1.INTRODUCTION The document describes the installation, commissioning, maintenance and troubleshooting of the following high voltage battery listed below. 1 I ntroduction ..................... 1 2 Symbols......................1 The battery chemistry of these products is Lithium Iron Phosphate. This manual is designed for qualified personnel only. -
Page 3: Safety
3.2 Installation 2. HVC-BCU is the controller of the whole system, so each system must have one HVC-BCU; 3. Our system consists of at least 1 HVC-BMU + 1 HVC-BCU and up to 5 HVC-BMU + 1 · After unpacking, please check the product for damages and missing parts. -
Page 4: Bms Specifications
Package Dimension(MM) 712x482x403 5.3 Battery System Specifications SPECIFICATIONS FOR BATTERY SYSTEM BATTERY SYSTEM HVC-5.1 HVC-10.2 HVC-15.4 HVC-20.5 HVC-25.6 Battery Module HVC-BMU(5.12kwh,102.4V) Number of Modules Total Energy [Kwh] 5.12 10.24 15.36 20.48 25.6 Usable Energy [kWh] (90%DOD) 13.8 18.4 Nominal Voltage [V] 102.4... -
Page 5: Battery System Features
LiFePO4 Battery System LiFePO4 Battery System 6. ELECTRICAL CONNECTIONS 6.3 Battery box introduction 6.1Battery System Features The batteries have been fitted with multiple protection systems to ensure the safe operation of the system. Some of the protection system includes: • Inverter interface protection: Over voltage, Over current, External Short Circuit, Reverse Polarity,Ground Fault, Over Temp, In rush current. -
Page 6: Switch On / Off
LiFePO4 Battery System LiFePO4 Battery System 6.6 Switch On / Off FOR HVC-BMU Battery box x1 7.2 Product size information 370mm 600mm Make life full of hope 7. INSTALLATION 7.1 Items in the package Packaging information • The battery system consists of a battery, a control box, and a base. -
Page 7: Floor Installation With Base
LiFePO4 Battery System LiFePO4 Battery System 7.4 Floor installation with base Step 1: Installation Location Requirements Wall Make life full of hope Make life full of hope ≥300mm ≥300mm 90° 90° Ground Ground Step 1: Step 2: Step 3: Make life full of hope 300≤d≤500 Make life full of hope... -
Page 8: Install Environment
LiFePO4 Battery System LiFePO4 Battery System Step 6: Step 7: 7.7 System Wiring Schematic Matching side inverter IVGM100600 Make life full of hope Make life full of hope Make life full of hope Note: 1.Check that the ground is flat and free of tilt before installation. 2.Make sure that the base is vertical and close to the ground. -
Page 9: Terminal Connection
LiFePO4 Battery System LiFePO4 Battery System Note:Press the position indicated in the figure above before disconnecting the power terminal. 7.9 Power line connection Install the waterproof Crimping power line Tighten the rear cover cover and rear cover Inverter end 7.10 Terminal Connection Power terminal 7.12 Description for Communication port Press... - Page 10 LiFePO4 Battery System LiFePO4 Battery System 8.1 Fault Code Table 7.13 Install protective cover EXPLAIN FAULT CODE TREATMENT MEASURE Battery Voltage High Battery Voltage Low Cell Voltage High Cell Voltage Low Electrical Connection Installation of protective cover Charging Current High Discharging Current High Grounding protection Bms Temperature High...
-
Page 11: Maintenance
LiFePO4 Battery System LiFePO4 Battery System 9. WARRANTY The warranty shall not cover the defects caused by normal wear and tear, inadequate maintenance, handling, storage faulty repair, modifications to the battery or pack by a third party other than Felicity, failure to observe the product specification provided herein or improper use or installation, including but not limited to the following.