Application Advice; Maintenance & Service; Declaration Of Conformity - Skil 1830 Original Instructions Manual

• Proper guiding %
- keep in mind that router bit turns clockwise
- guide tool so that bit turns into the workpiece, not
away from it

APPLICATION ADVICE

• Use the appropriate router bits ^
• For cuts parallel with the side of your workpiece use rip
fence
• For making parallel cuts in a workpiece far from the
edge #
- fasten a straight piece of wood on the workpiece by
means of 2 clamps
- guide tool with base-plate along edge of wood which
now functions as a rip fence
• When using bits with a pilot or ball bearing, the pilot or
ball bearing should slide along the edge of the
workpiece which should be perfectly smooth &
• For larger routing depths, it is recommended to carry
out several repetitive cuts with lower removal rates
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially ventilation
slots V 3)
! disconnect the plug before cleaning
• Lubricate sliding bars W 3 occasionally
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol * will remind you of this when the need for
disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60745, EN 55014, in
accordance with the provisions of the directives
2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
20.01.2010
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 85 dB(A) and the sound
power level 96 dB(A) (standard deviation: 3 dB), and the
vibration 4.7 m/s² (hand-arm method; uncertainty K =
1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
F
Défonceuse
INTRODUCTION
• L'outil est conçu pour le fraisage des rainures, bords,
profi ls et rainures droites dans le bois, les matières
plastiques et matériaux de construction légers ainsi que
pour le fraisage par copiage
• Lisez et conservez ce manuel d'instruction 2
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 3 4
A Blocage de l'arbre
B Chapeau
C Clé
D Levier de verrouillage
E Bouton de réglage (jauge de profondeur)
F Jauge de profondeur
G Tourelle de butées de profondeur
H Molette pour régler la vitesse
J Plaque adaptatrice
K Adaptateur de l'aspirateur
L Guide parallèle
M Tiges du guide parallèle
N Semelle
12
Jan Trommelen
Approval Manager
1830