Technical Data; Before Starting The Equipment - EINHELL RT-TC 520 U Original Operating Instructions

4. Technical data

Motor rating ............................................... 800 W
Motor speed ......................................... 3000 rpm
AC motor ....................................... 230 V ~ 50 Hz
Insulation material class .......................... Class B
Protection type ............................................. IP54
Table size ...................................... 570 x 385 mm
Cut length .............................................. 520 mm
Jolly length .............................................. 520 mm
Max. workpiece thickness 90° .................. 30 mm
Max. workpiece thickness 45° .................. 25 mm
Diamond wheel ........................... Ø 200 x Ø 25.4
Laser class ........................................................ 2
Laser wavelength ..................................... 650 nm
Laser output ............................................. < 1 mW
Laser power supply ...................... 2 x 1.5 V (AAA)
Weight .........................................................31 kg
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
With-load operation
L sound pressure level ........................ 94 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 107 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
No-load operation
L sound pressure level ........................ 76 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 89 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Anl_RT_TC_520_U_SPK1.indb 18 Anl_RT_TC_520_U_SPK1.indb 18
GB
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
•
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a
work bench, the base frame supplied in deli-
very, or similar.
•
All covers and safety devices must be cor-
rectly attached before the machine is used for
the first time.
•
The cutting wheel must rotate smoothly.
Assembly (Fig. 1-6)
•
Fasten the feet (18) to the base frame (12)
with the 4 screws (19).
•
Turn the sub-frame upright.
•
Insert the two screws (37) for the trough fix-
ture through the square holes and place the
trough (3) in the base frame (12).
•
Fasten the cooling water pump (13) to the
mount (38). Place the tile cutter into the
trough and screw on the trough fixture (39).
•
Unscrew and remove the star handle screw
(11) and spacer (40) and keep them in a safe
place.
•
Fill the trough with water until the cooling wa-
ter pump (13) is completely immersed.
Important!
To guarantee proper operation, the cooling water
hose (14) must not be kinked during installation.
- 18 -
30.08.12 12:54 30.08.12 12:54