Advertisement
AMPLIFIER FEATUER DESCRIPTIONS
MAXPIZOON
o
~.
I. Une Out RCA Jacks·
The UNE OUT allows you to build multiple amplifier systems
without having to use splitter cords to distribute the signal. Now it is simple a matter of
bringing one set of RCA> into the first amplifier. then using the line out RCA jacks as the
feed to the next amplifier.
Z.
Une Input
RCA Jacks • These inputs are for signal cables from the source.
Always use high quality shielded RCA cables.
3.
Input Level Controls·
Enables the matching of input levels to the output levels
from the head unit! or other signal source/.
4.
Phase Shift·
Allows you to change the phase of your subwoofer from 0 to 180
degrees to help compensate for timing differences between drivers.
Amplifier Feature Descriptions:
BALANCED INPUT:
Accepts balanced line inputs from 0.4 volts to 18 volts.
UNE INPUT:
The Une Inputs are the RCA input jacks labeled 'UNE INPUT". This is where
the Radio/CD player RCA outputs connect to. The Une Inputs accept unbalanced RCA inputs
from 0.2 volts to 9 volts.
UNE OUTPUT:
The Une Outputs are a direct pass-through from the inputs. The RCA input
signal from the radio/CD player is routed through the amplifier and out of the
Une
Outputs.
The outputs would connec.t to another amp Line Inputs in a multi-amp set-up. This allows you to
daisy chain multiple amps
from
a single set of RCA cables from the radio/CD player.
LEVEL: The input level control allows you to match the amplifier input sensitivi1;Y to the
output level of the RADIO/CD player from 0.2
Volts
to 9 volts when using unbalanced RCA
cables. The Level control needs to be adjusted to match the Line Level Sensitivity (this is the
amount of voltage the radio/CD player RCA's provide. Example: If the radio/CD player Line
Level Sensitivity is 4 volts, adjust the amp level control to 4 volts
SUBSONIC:
The variable Subsonic filter is for subwoofer applications that require very low
tuning frequencies typically around 15Hz - 35Hz.
BASS EO:
Variable Bass Boost from 0 to I Od8 at a fixed 45Hz.
LOW PASS:
Fully adjustable crossover from 35 to 250Hz.
MAXPI055DN/MAXPIZOIDN/MAXPI60IDN
MAXPZ05 1 DN/MAXPZ65 1 DN/MAXPZ055DN
5.
Remote Sub_ofer Control
6.
Variable Bass Boost Control·
0 - + I OdB
7.
Variable Subsonic Filter -
15Hz-35Hz
8.
Low Pass Filter·
When Crossover Mode Selector is in Low Pass Mode. this control
limits the frequencies which will be distributed to the speakers to those below the
value to which this is set within the range 35Hz-250Hz.
9.Power
&
Protection Indicators-
Provde instant information on status of amplifier.
including short-circuit and thermal overload alerts.
10.
Balancecllnput:
Accepts line level balanced input from 0.4vto lav.
PHASE SHIFT:
The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to
control the timing of the subwoofers. This is commonly used when the subwoofers are installed
in each front door.
SYSTEM DIAGNOSTICS:
The amplifier has built-in monitoring devices and protection
circuits that monitor all vital functions of the amplifier. The Protec.tion light does not come on
to indicate there is a failure, it comes on when it detects an improper operation. Common
issues that cause.
Protection status are:
• THERMAL:
The amp has an internal temperature sensor that will automatically shut off the
amp
if
it reaches dangerous temperature levels.
• OVER LOAD:
If the amp is run at an improper impedance, the amp will shut down. If you are
"CLIPPING" speakers / subwoofer!s/. the light will blink to indicate a hard Clip.
• DC
PROTECT:
In the unlikely event the amp should internally fail, the amp will shut down
to prevent a DC voltage output to the speakers or sub.
REMOTE:
The Remote Module plugs into the Remote jack and allows you to adjust
the level.
Advertisement
