Table of Contents
Advertisement
PROGRAMMED OPERATION
• Please check that there are no children or pets in the vicinity of the unit before use.
1. Press
• The ON/OFF lamp will come on.
1
• You can now select either strong or gentle or one of the manual settings
neck roller position
reclining
2. Select the Program You Want
3
• See Page 21 for details regarding the content of each of these
programmed
manual
/
Vigorously Massage the Whole Back
operation
operation
• Strong uses mainly a kneading massage and Shiatsu massage to
programmed operation
storong
gentle
• This type of massage is ideal for
2
whole back
neck, shoulder
lower back
• Massage starts out predominantly in
4
Gently Massage the Whole Back
vibration on/off
tap on/off
• This type of massage is ideal for
5
• It is gentler than shiatsu massage -
The Selected Program will Start
• It is possible to change the program
selected and the desired movement
mid-way through a massage.
• In Programmed Operation, the leg massage begins at the same time.
It is possible to stop or change the intensity of the leg massage during the program. (Please see Page 18.)
• When retracting the backrest, as the massage heads must be retracted in the interests of safety there may be
a slight delay before the backrest actually starts to retract. Please continue to hold down the Reclining Button
until the backrest is fully retracted.
The Seat Automatically Reclines to the Massage Position
• Initial position if auto recline is for both back and open ottoman operation. (for soles and feet.)
• To recline further, please use the recline button, but it is not recommended to keep the ottoman open.
Normal Position
(EP1061)
Normal Position
(EP1060)
3. Adjusting Shoulder Position
• When programmed operation begins, the seat automatically reclines to the massage position where the
massage heads carry out a Shiatsu massage in the area around the shoulders. During the time that the
Shoulder Position Indicator is flashing (approx. 20 seconds), use the Shoulder Position Adjustment Button to
adjust the position of the massage heads, limiting how high they will go.
Approximate positions for adjusting the position of the rollers are shown below.
• It is possible to change the position of the rollers
during the massage.
• As the position of the shoulders will change when
the reclining angle is changed during a massage,
please readjust the shoulder position every time
you change the reclining angle.
14
button
that can be accessed by opening the cover of the controller.
programs.
relax stiff muscles.
programmed operation
strong
people with stiff muscles
throughout their entire back.
the upper back.
programmed operation
strong
people who are feeling tired or weary.
more like a sewedish palm massage.
Massage Position
Approx. 3° Reclined
Reclining
In this comfortable
position it is possible to
massage from the neck
Approx. 14°
to the soles of the feet.
Raised
Massage Position
Approx. 14° Reclined
Reclining
In this comfortable
position it is possible to
massage from the neck
Approx. 60°
to the soles of the feet.
Raised
Up
Down
Approximate Body Height
neck roller position
neck roller position
Press
Press
• 5-stage (up-down approx. 4in.) adjustment.
• When the Shoulder Position Indicator is flashing, adjust the position of
the massage heads (upper roller) so that they lightly touch the shoulder.
• The shoulder position can be adjusted up and down 4in. (10cm).
• When it is not possible to correctly adjust the shoulder position, slide
your body down and try adjusting it again.
4. Selecting an Area for Concentrated Massage
• Please see Page 21–23 for details regarding the programs.
Massaging the Neck and Shoulders
• Press this button to focus the program on the neck
and shoulders.
(The upper and lower
back will also be
massaged slightly.)
gentle
• Press the button
again to toggle off.
whole back
Press
5. Removing Vibration and Tapping from Programs
Removing Vibration from Programmed Operation
gentle
• Press this button to remove vibration in programmed
whole back
operation. (The vibration will change to a kneading
massage.)
* Press the button
Press
again to restore
vibration to the
program.
• For Tapping B, and Vibration, unless the massage heads are actually touching the body then you may not feel
anything.
6. Adjusting Massage Intensity
• Massage intensity can be adjusted up to 3 levels.
• When the massage heads reach their limit you will hear a "peep,
peep, peep" sound.
7. Auto Stop in Programmed Operation
When the selected program has been completed, the unit will automatically come to a stop.
(Although programmed operation lasts for approximately 15 minutes (12–17 minutes), this will vary according to
the shoulder position and program selected, whether or not tapping is on or off, and the weight of the person
using the unit.)
• The massage heads will move to the retracted position and stop.
• The ON/OFF lamp will flash until the heads have stopped moving.
• If you want to start another massage, please press
• Please rest at least 10 minutes between massages.
8. Stopping Programmed Operation
Press
• The ON/OFF lamp will continue to flash until the massage heads have returned to the retracted position.
9. Stopping the Massage Immediately
Press
• All movement will stop immediately.
neck roller position
• The massage heads will not return to the retracted position, which may make sitting in the seat somewhat
6.1ft
uncomfortable.
5.2ft
• Please press
4.6ft
Massaging the Lower Back
• Press this button to focus the program on the lower
neck, shoulder
lower back
• Press the button
Press
Removing Tapping from Programmed Operation
• Press this button to remove tapping in
* Press the button
vibration on/off
tap on/off
Press
button.
button to stop programmed operation.
button to stop programmed operation immediately.
button twice in order to return the massage heads to the retracted position.
Too high
Correct position
• Lightly touching the shoulder.
Too low
back.
(The neck and
neck, shoulder
lower back
shoulders will also be
massaged slightly.)
again to toggle off.
Press
programmed operation. (The tapping will change
to a kneading massage.)
vibration on/off
tap on/off
again to restore
tapping to the
program.
Press
Increasing massage intensity
Decreasing massage intensity
intensity
intensity
Press
Press
15
Advertisement
Table of Contents
