Table of Contents
Advertisement
Quick Links
FRRA Series
Fiber Optic Receiver/Distribution Amplifiers
Model
FRRA-S4A-860-43P
FRRA-S4S-860-43P
FRRA-S4A-1000
FRRA-S4A-1000
©2014 Blonder Tongue Laboratories, Inc. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of their respective owner.
Stock No.
7411P84B
7411P84BS
7411P14
7411P14S
Status
Date
ACTIVE
July 29, 2014
800-523-6049
www.blondertongue.com
860 MHz, FC/APC Connector
860 MHz, SC/APC Connector
1000 MHz, FC/APC Connector
1000 MHz, SC/APC Connector
Document No.
Issue No.
651210200 C
1
Stock No.
Stock No.
7411
7411
USER MANUAL
USER MANUAL
Author
KK
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Blonder tongue FRRA Series
Summary of Contents for Blonder tongue FRRA Series
- Page 1 1000 MHz, SC/APC Connector Status Date Document No. Issue No. Author ACTIVE July 29, 2014 651210200 C 800-523-6049 www.blondertongue.com ©2014 Blonder Tongue Laboratories, Inc. All rights reserved. Specifications are subject to change without notice. Trademarks are the property of their respective owner.
-
Page 2: Safety Precautions
Always double check that power is disconnected before using such devices. If possible, completely dis- connect the unit from any power source. If you have questions about laser safety procedures, please call Blonder Tongue before powering your product. Laser safety classes for the FRRA are as follows:... -
Page 3: Specifications
FRRA Instruction Manual Description The FRRA is a fiber optic receiver module integrated with a rack mounted broadband distribution amplifier (RMDA). The FRRA is used as a launch amplifier in a coaxial distribution sub-system fed from a single mode broadband fiber network. - Page 4 FRRA Configuration Table in Figure 4 for the corresponding optical input level conversion to mW and dBm. OUTPUT TEST OPTICAL POWER GAIN SLOPE POWER 1V/mW GROUND Figure 2 - Rack Mount Front Panel FLAT -20dB INPUT FRRA SERIES ALARM FIBER RECEIVER DISTRIBUTION AMP Figure. 2...
- Page 5 With the optical source and AC power connected, measure the RF signal level at “RF Loop” output connector. Choose the appropriate attenuator value to set this level to +5 dBmV, ± 5 dB. A Blonder Tongue model FAM-xx (Stock No.
-
Page 6: Maintenance
FRRA Instruction Manual Maintenance Cleaning If the units need to be cleaned, avoid the use of all solvents and use low-pressure clean air to remove loose dirt. Use low-pressure clean air to clear the connectors of any debris. Dirty or scratched connector end faces will greatly reduce the unit’s performance. -
Page 7: Troubleshooting
A Return Material Authorization (RMA) Number is required on all products returned to Blonder Tongue, regardless if the product is being returned for repair or credit. Before returning product, please contact the Blonder Tongue Service Department at 1-800-523-6049, Ext. 4256 or visit our website:... - Page 8 FRRA Instruction Manual NOTES...
- Page 9 FRRA Instruction Manual NOTES...
- Page 10 FRRA Instruction Manual NOTES...
-
Page 11: Extended Warranty Program
10. The cost of the extended warranty is 8% of the purchase price for a 1 or 2 year extension beyond the Blonder Tongue standard warranty. e.g. A product price of $1000 will be $80 for the 1 year (12 mos) and additional $80 for 2 year (24 mos) extension for a total of $160. -
Page 12: Limited Warranty
BT may determine) any product manufactured by BT which proves to be defective in materials or workmanship or fails to Blonder Tongue Laboratories, Inc. (BT) will at its sole option, either repair or replace (with a new or factory reconditioned product, as BT may the case of software, licensed) by Seller which is defective in materials or workmanship or fails to meet the applicable specifications that are in effect on the date of meet the specifications which are in effect on the date of shipment or such other specifications as may have been expressly...
Need help?
Do you have a question about the FRRA Series and is the answer not in the manual?
Questions and answers