Related Manuals for Hyundai HFBE10T105
Summary of Contents for Hyundai HFBE10T105
- Page 1 ELECTRIC LOG SPLITTER HFBE10T105 、 WARNING: Read thoroughly the instruction manual before using.
-
Page 2: Table Of Contents
CONTENTS 1. SAFETY INSTRUCTIONS........................3 2. YOUR PRODUCT..........................9 3. ASSEMBLY............................16 4. OPERATION............................18 5. MAINTENANCE AND REPAIR......................25 6. DISPOSAL............................25 7. DECLARATION OF CONFORMITY....................26 8. WARRANTY............................27 9. PRODUCT FAILURE.......................... 28 10. WARRANTY EXCLUSIONS......................29... -
Page 3: Safety Instructions
1. SAFETY INSTRUCTIONS GENERAL INFORMATION We wish you much joy and success in working with your new machine. Note: The manufacturer of this equipment shall not be liable in accordance with the applicable product liability law for damage caused by this device through: Improper treatment;... - Page 4 The splitting operation of the machine is designed to be activated by one person. While there is the possibility that additional operators could be working with the machine (e.g. for loading and unloading), only one operator should activate splitting operations. The machine shall not be used by children.
- Page 5 In case of danger, turn off the machine and disconnect the mains plug! No other person should be in the work area. Never split logs containing nails, wire or other objects. Already split wood and wood chips create a dangerous work area. There is a risk of stumbling, ...
- Page 6 The safety labels should always be clean and legible and be followed precisely to avoid accidents, but if the signs are damaged or lost or belong to parts that were exchanged, they must be replaced by new original signs to be requested from the manufacturer and attached at the designated places.
- Page 7 For transport using the hook, the crane lifting eye on the upper part of the machine should be used. Never lift on the splitter blade! Storage conditions: Please adhere to the following specifications: Dry, covered storage location Max. humidity 80% ...
- Page 8 Turning on/off Press the green button to turn on. Press the red button to turn off. Note: before every use, check the on/off switch unit for proper functioning by turning on and off once. Securing against restart in case of power outage (zero voltage trigger) In the case a power outage, accidental disconnection of the mains plug or defective fuse, the machine switches off automatically.
-
Page 9: Your Product
Caution! Switch off the engine before repair, maintenance and cleaning. Unplug the mains plug. Do not remove jammed trunks with your hands. Danger of bruising and injury from sharp edges; never touch danger areas when the cleaver is moving. 2. YOUR PRODUCT Description 1-Wheels, 7-Operation handle,... - Page 10 Technical Data Engine Electrical motor Input power(P1) 3.7kW Voltage 230V~/50Hz Motor speed 2800/min Operating mode S6/40% Splitting force 10ton Weight 169kg Protection class Cutting length 1060mm Size of log 70-400mm IP number IP54 Hydraulic pressure Max. 22MPa Sound power level 91dB(A) The specified values are emission levels and do not necessarily represent safe workplace values.
- Page 11 Hydraulic diagram Introduction of parts Fig1...
- Page 12 Fig2 Fig3...
- Page 13 Fig4 Fig.5...
- Page 14 Fig.6 Fig.7...
- Page 15 Fig.8 Fig.9 Fig.10...
-
Page 16: Assembly
3. ASSEMBLY Mount axle Fig.2 Insert axle through the hole in the base of splitter (No.2). Assemble the wheels Fig.2 Place 2 wheels (No.1) on both sides of the axle and secure it with a cotter pin (No.3) Assemble the control handle Fig.3 Because of packing reasons you must mount two control handles yourself. - Page 17 Assemble the support arm Fig.6 Fix two support arms with 3 bolts M10*45+1long special bolt, and 4 nuts.(with tool:17-19 wrench) Assemble the lifting device Fig.1 With 2 hexagonal bolts M10*25 and 2 nuts M10 to fix the support of lifting device. Then with 1 hexagonal bolts M10*55 and 1 nut M10 to connect the lifting device.
-
Page 18: Operation
Manual handling Transport by hand when transport, the cylinder must always be brought to the transport position. Fig.7 (the bleed screw must be sealed tight.) To this end, move the splitter blade with slight pressure on the support. (E.g. wooden block) Lower the cylinder by pressing the return bracket downwards or the handles upwards, but only to the extent that no connectors or cables are damaged. - Page 19 Release the air from the hydraulic system before putting the log splitter in operation. Loosen the bleed screw of the column tank by turning a couple of times until the air can flow in and out. The draught of the oil tank should be detectable. Before moving the log splitter, never forget to loosen the bleed screw (fig.
- Page 20 Never split logs that are lying down or across the grain direction! When splitting wood, wear appropriate safety gloves and safety shoes. In case of extremely overgrown wood, split the logs from the edge. Note: certain woods can come under severe stress and rupture suddenly during splitting. Knock out jammed wood against the cleavage direction or by moving the splitter wedge upwards.
- Page 21 CAUTION! Before delivery, while packing ， the cylinder must be descended from top position to the lowest position, and fixed in the fixing part of the cylinder (Fig.9 cylinder fixing part). According to the followings: Press the two operation handles downwards, the riving knife begins to work forward ,until to the cylinder fixing part , release one operation handle, pull out two R-pins and two shafts( Fig.4 ),then operate the two operation handles upward , the cylinder begin to descend, till to the proper position, release two operation handles, stop the machine, and put two shafts, two R-pins...
- Page 22 Operation of the log lifter General information on log lifter: The chain of the log lifter may be suspended only at the last link at the suspension plate for safety reasons. Make sure that there are no persons in the work area of the log lifter. Operation of the log lifter Loosen the retaining hooks on the log lifter, so that the lifting rod can move freely Move the splitter blade down until the lifting rod of the log lifter completely rests on the floor.
- Page 23 An imprint of the type designation on the power cable is mandatory. The mains supply at the customer must be protected by an RCD (Residual Current Device) with a rated residual current of maximum 30mA. Faulty power supply cables Insulation damage often occurs on power supply cables. Causes are: Pressure points when power supply cables are routed through the window or door gaps.
- Page 24 through the two inspection windows which are on the splitting column. If the oil level is at the lower window, this corresponds to the minimum oil level. If this is the case, oil should be refilled immediately. The upper window indicates the maximum oil level. The oil tank is in the splitting column and is factory-filled with high grade hydraulic oil.
-
Page 25: Maintenance And Repair
Error Elimination Fault Possible Causes Solution Danger level Risk of electric shock. This operation must be Voltage is absent Check if the cables are live. performed by a service The hydraulic Electrician. pump is not Thermal switch turns on running The motor thermal again after the motor cools switch has turned... -
Page 26: Declaration Of Conformity
EC Directives listed below. In case of modifications to the machine, the present declaration loses its validity. Designation of the machine: ELECTRIC LOG SPLITTER Model: HFBE10T105 S/N: 20230507936-20230507977 Relevant EC directives:... -
Page 27: Warranty
8. WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 28: Product Failure
9. PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank if your product has one. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 29: Warranty Exclusions
10. WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...