1. SAFETY 1.1. General safety notes. 1.1.1. The operator of the machine is responsible for, and has a duty of care in making sure that the machine is operated safely and in accordance with the instructions in this user manual. Keep the manual safe and pass it on if the machine loaned/sold to another user.
Page 4
1.2. Electrical safety (where applicable). 1.2.1. Electricity can kill - NEVER work on LIVE/ENERGISED equipment. 1.2.2. Prior to carrying out any maintenance work you MUST Identify electrical isolation methods and isolate all electrical supplies, 1.2.3. Prior to use and with all electrical supplies isolated You MUST check all electrical cables, plugs and connections for the following;...
1.4.2. Noise emissions for this equipment is unavoidable. Carry out noisy work at approved times and for certain periods. Limit the working time to a minimum. For your personal protection and protection of people working nearby it is also advisable for them to wear hearing protection. 1.4.3.
Page 6
2.6.2. DO NOT put the log splitter on the ground for operations. This is awkward operating position that the operator has to bring his face close to the machine, and thus risks being struck by wood chips or debris. 2.7. Extension leads. 2.7.1.
Page 7
2.14. Do not force machine. 2.14.1. It will do a better and safer job at its design rate. NEVER try to split logs larger than those indicated in the specifications table. This could be dangerous and may damage the machine. 2.14.2.
3. PARTS LOCATIONS 3.1. Locations. 1 – Log pusher 2 – Work table 3 – Wedge 4 – Lift handle 5 – Support leg 6 – Log retaining plate 7 – Motor 8 – Switch 9 – Pushbutton box 11 – Wheels – for only minor 10 –...
Page 9
Stand assembly (optional HYLS4000H). Unplug unit from the mains supply. Remove existing support leg then follow steps 3 & 4 below. Support leg Page 9...
Page 10
3.2.1. Max pressure was set before the log splitter ex work and the max pressure limiting screw is sealed with glue to ensure the log splitter works under pressure no more than 4 tons HYLS4000H/7 tons HYLS7000H. The setting was done by qualified mechanic with professional instruments. Un-authorised...
5. OPERATION 5.1. Operating the HYLS4000H. 5.1.1. This log splitter is equipped with a control system that requires the machine to be operated by both hands of the user- Left hand controls the hydraulic control lever while right hand controls the pushbutton switch.
Page 13
Never force the log splitter for more than 5 seconds by keeping pressure on it to split excessively hard wood. 5.2.3. After this time interval, the oil under pressure will be overheated and the machine could be damaged. For such extremely hard log, rotate it by 90° to see whether it can be split in a different direction.
Page 14
5.5. Replacing hydraulic oil HYLS4000H. 5.5.1. Replace the Hydraulic oil in the log splitter after every 150 hours of use. Take following steps to replace it. 5.5.2. Make sure all moving parts stops and the log splitter is unplugged. 5.5.3. Unscrew Oil Drain Bolt with Dipstick to remove 5.5.4.
5.7. Recommended oil. 5.7.1. Following hydraulic oils or equivalent are recommend for the log splitter's hydraulic transmission system: 5.7.2. SHELL Tellus 32 5.8. Sharpening wedge 5.8.1. After using the log splitters for some time, it will need sharpening. Sharpen the wedge of the log splitter by using a fine-toothed file and smooth any burrs or crushed area along the cutting edge.
Page 16
7. PARTS SCHEMATIC 7.1. HYLS4000H Page 16...
8. PRODUCT DISPOSAL 8.1. Should it become necessary to dispose of your machine please contact your local authority for the disposal advice, or take unit to your local recycling centre. 8.2. You MUST make sure that all unused oil, fuel and batteries are disposed of correctly either beforehand or at amenity centre.