SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
Do not exceed the maximum load of 9 kg (refer to the • "Programme chart" chapter). The operating water pressure at the water entry point from the • outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a •...
ELECTRICAL CONNECTION • You can extend the drain hose to maximum 400 cm. Contact the Authorised Service Centre for WARNING! Risk of fire and electric the other drain hose and the extension. shock. • The appliance must be earthed. WARNING! Risk of injury, electric •...
PRODUCT DESCRIPTION APPLIANCE OVERVIEW Worktop Detergent dispenser Control panel Door handle Rating plate Feet for levelling the appliance FIXING PLATE KIT (4055171146) Available from your authorised dealer. If you install the appliance on a plinth, secure the appliance in the fixing plates. Read carefully the instructions supplied with the accessory.
: Cold water indicator • : The alarm codes : The permanent extra rinse indicator • : The message of error C. The spin area: • : Programme is completed. • : The spin speed indicator : The door locked indicator •...
Page 8
Maximum load Programme Programme description Maximum spin Temperature range (Type of load and soil level) speed 2 kg Special programme for cotton, synthetic and mixed Mixed Fabrics 1200 rpm fabrics with light soil. In case of setting cold wash cycle 60°C - Cold make sure to use the detergent designed for low tempera- tures.
CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards. Different cau- ses can change the data: the quantity and type of laundry and ambient temperature. Wa- ter pressure, the supply voltage and the temperature of inlet water may also affect the washing programme duration.
Page 10
Off Mode (W) Left On Mode (W) 0.30 0.30 The information given in the chart above is compliant with the EU Commission regulation 1015/2010 implementing directive 2009/125/EC . OPTIONS TEMPERATURE To drain the water refer to ‘At the end With this option you can change the default of the programme’.
EXTRA RINSE FINISH AT With this option you can add some rinses to a With this option you can set the exact time in which washing programme. you would like your washing programme to be Use this option for persons allergic to detergents completed.
• you activate the appliance for the first time after 5. Touch the button to confirm the selection. it has been unplugged for more than two weeks, • you did not confirm the time selection within 15 The appliance enters automatically in seconds period from last button touching, clock setting mode when: •...
2. If necessary, change the temperature and the To use liquid detergent: spin speed or add available options. When you 1. Remove the drawer. activate an option, the indicator of the set Push the drawer edge in option comes on. the place with the arrow (PUSH) to remove the If you set something incorrect, the...
Page 14
To open the door during the first minutes of You can cancel or change the set of the cycle (or when the operates) : the option before you touch the 1. Touch the button to pause the appliance. button . After touching the button 2.
Press the button to activate the appliance The appliance drains and spins again. automatically after approximately 18 • After 5 minutes from the end of the washing hours (except for Wool programme). programme. Press the button to activate the appliance AUTO-OFF OPTION again.
Use the correct quantity of the water softener. Obey the instructions that you find on the packaging of the product. CARE AND CLEANING MAINTENANCE WASH WARNING! Refer to Safety chapters. With the low temperature programmes it is possible that some detergent stays in the drum. Perform a maintenance wash regularly.
CLEANING THE INLET HOSE AND THE VALVE FILTER 45° 20° FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump.
early. If the alarm code appears again, contact WARNING! Deactivate the appliance the Authorised Service Centre. before you do the checks. POSSIBLE FAILURES Problem Possible solution The programme does not • Make sure that the mains plug is connected to the mains socket. start.
Problem Possible solution The appliance makes an • Make sure the levelling of the appliance is correct. Refer to 'Installa- unusual noise. tion instruction'. • Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation instruction'. •...
Spin Speed Maximum 1400 rpm 1) The appliance works correctly if the water pressure is not lower than 0.05 MPa (0.5 bar). If you cannot connect the water inlet hose to the cold water tap of the primary hydraulic system, connect it to your do- mestic cold water storage system.