Roland RG-3 Midi Implementation Manual page 25

● 0103: HUMANIZER
Adds a vowel character to the sound, making it similar to a human voice.
No Parameter Value Default
1 Drive Sw 0 - 1 OFF, ON
2 Drive # 0 - 127 0-127
3 Vowel1 0 - 4 a, e, i, o, u
4 Vowel2 0 - 4 a, e, i, o, u
5 Rate sync 0 - 1 Hz, note
6 Rate 1 - 127 0.05-10.00 Hz
7 Rate # 0 - 21 note (*1)
8 Depth 0 - 127 0-127
9 Input Sync Sw 0 - 1 OFF, ON
Input Sync
10 0 - 127 0-127
Threshold
11 Manual 0 - 100 0-100
12 Low Gain 0 - 30 -15- +15 dB
13 High Gain 0 - 30 -15- +15 dB
14 Pan 0 - 127 L64-63R
15 Level 0 - 127 0-127
● 012b: RING MODULATOR
This is an effect that applies amplitude modulation (AM) to the input signal, producing bell-
like sounds. You can also change the modulation frequency in response to changes in the
volume of the sound sent into the effect.
No Parameter Value Default
1 Frequency # 0 - 127 0-127
2 Sens 0 - 127 0-127
3 Polarity 0 - 1 UP, DOWN
4 Low Gain 0 - 30 -15- +15 dB
5 High Gain 0 - 30 -15- +15 dB
D100:0W-
6 Balance # 0 - 100
D0:100W
7 Level 0 - 127 0-127
● 0125: TREMOLO
Cyclically modulates the volume to add tremolo effect to the sound.
No Parameter Value Default
TRI, SQR,
1 Mod Wave 0 - 4 SIN, SAW1,
SAW2
2 Rate sync 0 - 1 Hz, note
3 Rate # 1 - 127 0.05-10.00 Hz
4 Rate 0 - 21 note (*1)
5 Depth # 0 - 127 0-127
6 Low Gain 0 - 30 -15- +15 dB
7 High Gain 0 - 30 -15- +15 dB
8 Level 0 - 127 0-127
● 0126: AUTO PAN
Cyclically modulates the stereo location of the sound.
No Parameter Value Default
TRI, SQR,
1 Mod Wave 0 - 4 SIN, SAW1,
SAW2
2 Rate sync 0 - 1 Hz, note
3 Rate # 1 - 127 0.05-10.00 Hz
4 Rate 0 - 21 note (*1)
5 Depth # 0 - 127 0-127
6 Low Gain 0 - 30 -15- +15 dB
7 High Gain 0 - 30 -15- +15 dB
8 Level 0 - 127 0-127
Description
Turns Drive on/off.
Degree of distortion
Also changes the volume.
Selects the vowel.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency at which the two vowels
switch (Hz)
Frequency at which the two vowels
switch (note)
Effect depth
Determines whether the LFO for
switching the vowels is reset by the
input signal (ON) or not (OFF).
Volume level at which reset is ap-
plied
Point at which Vowel 1/2 switch
49 or less: Vowel 1 will have a long-
er duration.
50: Vowel 1 and 2 will be of equal du-
ration.
51 or more: Vowel 2 will have a
longer duration.
Gain of the low frequency range
Gain of the high frequency range
Stereo location of the output
Output level
Description
Adjusts the frequency at which mod-
ulation is applied.
Adjusts the amount of frequency
modulation applied.
Determines whether the frequency
modulation moves towards higher
frequencies (UP) or lower frequen-
cies (DOWN).
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct
sound (D) and the effect sound (W)
Output level
Description
Modulation Wave
TRI: Triangle wave
SQR: Square wave
SIN: Sine wave
SAW1/2: Sawtooth wave
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the change (Hz)
Frequency of the change (note)
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
Description
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the change (Hz)
Frequency of the change (note)
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
● 012c: SLICER
By applying successive cuts to the sound, this effect turns a conventional sound into a
sound that appears to be played as a backing phrase. This is especially effective when
applied to sustain-type sounds.
No Parameter Value Default
1 Rate sync 0 - 1 Hz, note
2 Rate 1 - 127 0.05-10.00 Hz
3 Rate # 12 - 21 note (*1)
4 Attack 0 - 127 0-127
5 Input Sync Sw 0 - 1 OFF, ON
Input Sync
6 0 - 127 0-127
Threshold
LEGATO,
7 Mode 0 - 1
SLASH
8 Shuffle # 0 - 127 0-127
9 Level 0 - 127 0-127
● 0130: COMPRESSOR
Flattens out high levels and boosts low levels, smoothing out fluctuations in volume.
No Parameter Value Default
1 Attack # 0 - 127 0-127
2 Threshold # 0 - 127 0-127
3 Post Gain 0 - 18 0- +18 dB
4 Low Gain 0 - 30 -15- +15 dB
5 High Gain 0 - 30 -15- +15 dB
6 Level 0 - 127 0-127
● 0131: LIMITER
Compresses signals that exceed a specified volume level, preventing distortion from
occurring.
No Parameter Value
1 Release 0 - 127 0-127
2 Threshold # 0 - 127 0-127
1.5:1, 2:1, 4:1,
3 Ratio # 0 - 3
100:1
4 Post Gain 0 - 18 0- +18 dB
5 Low Gain 0 - 30 -15- +15 dB
6 High Gain 0 - 30 -15- +15 dB
7 Level 0 - 127 0-127
MIDI Implementation
Description
When this is set to "note," the effect is
synchronized with the tempo.
Rate at which the 16-step sequence
will cycle (Hz)
Rate at which the 16-step sequence
will cycle (note)
Speed at which the level changes be-
tween steps
Specifies whether an input note will
cause the sequence to resume from
the first step of the sequence (ON) or
not (OFF)
Volume at which an input note will
be detected
Sets the manner in which the volume
changes as one step progresses to the
next.
LEGATO: The change in volume
from one step's level to the next re-
mains unaltered. If the level of a fol-
lowing step is the same as the one
preceding it, there is no change in
volume.
SLASH: The level is momentarily set
to 0 before progressing to the level of
the next step. This change in volume
occurs even if the level of the follow-
ing step is the same as the preceding
step.
Timing of volume changes in levels
for even-numbered steps (step 2, step
4, step 6...).
The higher the value, the later the
beat progresses.
Output level
Description
Sets the speed at which compression
starts
Adjusts the volume at which com-
pression begins
Adjusts the output gain.
Gain of the low frequency range
Gain of the high frequency range
Output level
Description
Adjusts the time after the signal vol-
ume falls below the Threshold Level
until compression is no longer ap-
plied.
Adjusts the volume at which com-
pression begins
Compression ratio
Adjusts the output gain.
Gain of the low frequency range
Gain of the high frequency range
Output level
25