Bosch 0 601 6A9 020 Original Instructions Manual page 9

(29) Cutting depth scale
B)
(30) Pair of screw clamps
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
B) Commercially available (not included in the scope of deliv-
ery)
Technical Data
Hand-held circular saw
Article number
Rated power input
No-load speed
Max. cutting depth with 165 mm saw blade diameter
– at a 0° mitre angle
– at a 45° mitre angle
Spindle lock
Base plate dimensions
Max. saw blade diameter
Min. saw blade diameter
Max. base blade thickness
Locating bore
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-5.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 91 dB(A); sound power level
102 dB(A). Uncertainty K = 3 dB.
Wear hearing protection
Total vibration values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-5:
2
Sawing wood: a = 1.6 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to compare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The given vibration level and noise emission value represent
the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
Bosch Power Tools
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
GKS 600
Fitting
3 601 FA9 0..
W 1200
Only use saw blades the maximum permitted speed of
u
rpm 5200
which is higher than the no-load speed of the power
tool.
mm 55
Inserting/changing the circular saw blade
mm 37
Pull the plug out of the socket before carrying out any
u
●
work on the power tool.
mm 235 x 138
Wear protective gloves when fitting the saw blade.
u
mm 165
Danger of injury when touching the saw blade.
mm 160
Only use saw blades that match the specifications
u
given in this operating manual and on the power tool.
mm 2.2
The permitted speed of the application tool must be at
u
mm 20
least equal to the maximum speed marked on the
kg 3.6
power tool. If accessories run faster than their rated
speed, they may break and fly off.
/ II
Do not use abrasive wheels as the application tool un-
u
der any circumstances.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions.
Removing the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
– Press and hold the spindle lock button (3).
Do not press the spindle lock button (3) while the saw
u
spindle is moving. The power tool may become damaged
if this happens.
– Use the hex key (17) to undo the clamping bolt (18) in ro-
2
tational direction ➊.
– Swing the retracting blade guard (10) back and hold on
to it firmly.
– Remove the clamping flange (19) and the saw blade (20)
from the saw spindle (22).
Fitting the saw blade (see figure A)
To change tools, we recommend that you place the power
tool down on the front side of the motor housing.
– Clean the saw blade (20) and all the clamping elements
to be fitted.
– Swing the retracting blade guard (10) back and hold on
to it firmly.
English | 9
1 609 92A 4DJ | (19.09.2018)