Hamilton Beach 40996 - 1.7-Liter Programmable Kettle Manual

Hamilton Beach 40996 - 1.7-Liter Programmable Kettle Manual

Advertisement

Hamilton Beach 40996 - 1.7-Liter Programmable Kettle Manual

Parts and features

Parts and features

  1. Push-Button Lid
  2. Removable Anti-Scale Mesh Filter (inside spout)
  3. Power Base
  4. Control Panel/Display
  5. Water Level Window

Control Panel/Display

Control Panel/Display

How to use the kettle


Burn Hazard. Do not overfill kettle. Boiling water may spit out of the spout.

BEFORE FIRST USE: Flip open lid and fill kettle with water to the MAX fill line on the water level window. Press ON/OFF (I/O) button to turn the kettle ON (I). The kettle will bring the water to a boil, then shut off automatically. Discard water and repeat 2–3 times, rinsing out the kettle each time. The kettle is now ready for use.

  1. Remove kettle from power base before filling.
  2. Fill kettle with required amount of water. Ensure that water level is between 0.5 L and MAX on the water level window. Always keep mesh filter in place.
  3. Make sure the lid is closed and the power base is on a level surface.
  4. Plug into outlet and turn ON (I). The lighted switch indicates that the kettle is ON. Current water temperature is shown on the display.
  5. Set desired water temperature (see "Programming water temperature" section) or just let kettle bring water to a boil (212°F/100°C).
  6. The 60-minute Keep Warm cycle will begin and the Keep Warm/ light will illuminate when the water has reached the desired temperature. The current water temperature and remaining Keep Warm time will alternate in the display. (Remember, the surface of the kettle gets hot; take care─only grip the kettle by the handle).
  7. After 1 hour, the ON (I) light turns off, the Keep Warm/ light turns off, and the current water temperature is displayed.
  8. The kettle may be left on the base once water is heated, but it is recommended to turn OFF (O) the kettle and unplug the cord from the outlet. When finished, make sure cord is unplugged and empty any water from the kettle.

NOTE: Only use kettle to heat water. If kettle is used to heat other liquids, such as coffee or tea, the warranty will be voided.

Change from Fahrenheit to Celsius

Press the + and buttons at the same time to show the water temperature in °C. Press + and buttons again to show °F.

Programming water temperature

To choose a preprogrammed water temperature:

  1. Press the PROG button repeatedly until the temperature you desire shows on the display; then release button. Starting at 212°F/100°C, several preset temperatures will cycle through the display.

To set a custom water temperature:

  1. To set a custom water temperature, press the PROG button to see the current temperature setting. Press the + or buttons to change the desired temperature in 5°F/2–3°C increments and then release.

NOTE: 150°F/65°C is the minimum temperature that can be programmed.

Setting clock time

To set the clock:

  1. Plug in kettle.
  2. To set the time of day, press and hold the + button for several seconds to set the current hour. For PM, the PM indicator light will illuminate.
  3. Press the + or buttons for less than 1 second to change the time in minutes until you reach the current time.

NOTES: If the + or buttons are not pressed again within 3 seconds, then the kettle displays the current water temperature. Clock time must be set for the AUTO ON function to work.

Programming AUTO ON

To set and use AUTO ON:

  1. Make sure clock is set for the correct time of day.
  2. Fill kettle with desired amount of water and place on power base.
  3. Press and hold PROG and + to display 19:99 or the last programmed time.
  4. Use + and buttons to set the AUTO ON time.
  5. Momentarily press PROG and ON/OFF (I/O) at the same time to set the kettle to turn on automatically at the desired time.
  6. Momentarily press the PROG button again to cancel AUTO ON.
  7. Momentarily press the ON (I) button to cancel AUTO ON and begin heating.

NOTE: You cannot set the AUTO ON function if the clock has not been set.

If Kettle Floor Discolors: It is normal for stainless steel heating elements to discolor. This does not affect the performance of the kettle. Do not use abrasive scouring pads or cleaners since this may damage the stainless steel surface.

If Kettle Boils Dry: The heating element is protected by two automatic safety devices. If your kettle is accidentally switched on without being filled with water, or is allowed to boil dry, the kettle will automatically switch off. You should:

  • Press ON/OFF (I/O) button to turn OFF (O), unplug, and wait about 20 minutes for the element to cool down.
  • Refill the kettle; then use as normal and check that the kettle functions correctly.

If Kettle Does Not Work: Make these simple checks before calling the toll-free customer assistance number:

  • Have you pressed the ON/OFF (I/O) button to ON (l) position?
  • If the kettle heats but does not boil, it might need descaling(see "Care and cleaning" section).
  • Has the kettle been accidentally turned on without being filled with water or allowed to boil dry? Press the ON/OFF (I/O) button to OFF (O), wait 20 minutes, and try again.
  • Is cord firmly plugged into the outlet and kettle firmly seated in the base?

Anti-Scale Mesh Filter: Scale is caused by lime and calcium in hard water. The mesh filter will prevent these suspended particles from being poured out of the kettle. The filter should be cleaned periodically to ensure optimum performance. To clean the filter, unplug kettle and allow to cool. The mesh filter may be removed by pressing down on filter tab, which is visible through the kettle opening, and pushing it towards the spout and sliding the filter up. Rinse filter under running water and brush with a soft brush. An old, clean toothbrush works well. To replace the mesh filter, slide the filter down into the spout and press down on the filter tab. Push the filter back until the filter tab latches into the kettle opening.
Anti-Scale Mesh Filter

Tea Guide

  • Bring filtered or good-tasting tap water to a boil in the kettle. Use 6 ounces (180 ml) of water per cup of tea.
  • If using loose tea instead of tea bags, measure 1 rounded teaspoon of tea per cup into an infuser and place the infuser in the cup. If no infuser is available, put the tea directly into the cup.
  • Pour heated water directly over the tea. For stronger tea, add more leaves rather than infusing longer than is recommended.
    NOTE: Tea that is oversteeped will become bitter.

NOTE: These temperature settings can vary depending on a number of factors, such as altitude, impurities in the water, and the amount of water in the kettle.

Preset Temperature & Tea Steeping Guide

Care and cleaning


Electric Shock Hazard. Do not immerse kettle, power base, or plug in water or any other liquid.

  1. With kettle unplugged, empty any remaining water and rinse. Allow kettle to cool. The mesh filter may be removed by pressing on filter tab, which is visible through the kettle opening. The filter will drop into the kettle cavity.
  2. To replace the filter in the spout, position the filter with tabs toward spout and press filter until it fits into place.
  3. To avoid scale/lime deposit buildup, empty kettle after each use. To remove discoloration or scale/lime deposit from heating element: Place 1/2 teaspoon (2.5 ml) cream of tartar (available in the spice aisle of grocery store) into the kettle. Then fill the kettle 1/2 full with water. Plug in, turn ON (I), and bring to boil. Turn OFF (O), let cool, and rinse several times with clean tap water.
  4. Wipe the exterior of kettle with a damp cloth. Do not use abrasive scouring pads or powders since they may scratch the smooth surface of the kettle.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Hamilton Beach 40996 - 1.7-Liter Programmable Kettle Manual

Advertisement

Need help?

Need help?

Do you have a question about the 40996 and is the answer not in the manual?

Questions and answers

Table of Contents