To Read Out (Beep Out) Radio Channel Contents; Fig-4: To Place The Radio In Program/ Readout Mode; To Place The Radio In Program/ Readout Mode - Ritron Jobcom JMX-152 Owner's Manual

HOW TO DETERMINE FREQUENCIES & TONE CODES IN YOUR JMX/ SST
IMPORTANT:
To talk to other users in your group, all radios must
be set to the same frequency and Quiet Call tone
code.
1. PRESS & HOLD UNTIL
THE "RADIO OFF"
TONES ARE HEARD,
THEN RELEASE.
2. PRESS & HOLD.
4. CONTINUE HOLDING THE PTT
UNTIL THE BEEPING STOPS,
THEN RELEASE IT.
The radio will emit a triple tone:
it is now in Program/ Readout Mode.
FIG-4: FIG-4: FIG-4: FIG-4: FIG-4: TO PLACE THE RADIO IN TO PLACE THE RADIO IN TO PLACE THE RADIO IN TO PLACE THE RADIO IN TO PLACE THE RADIO IN
PROGRAM/ READOUT MODE PROGRAM/ READOUT MODE PROGRAM/ READOUT MODE PROGRAM/ READOUT MODE PROGRAM/ READOUT MODE
page 3 RITRON, INC. 1-800-USA-1-USA (1-800-872-1872)
page 4

TO READ OUT (BEEP OUT) RADIO CHANNEL CONTENTS

1. To enter the Programming/ Readout Mode, refer to FIG-4 at left.
2. Press and release the On/ Volume Up button. The radio will begin to emit a series of beeps; each series of
beeps is equal to one digit of each two-digit frequency code or Quiet Call tone code programmed into the radio;
see Tables 1 and 2, opposite.
3. Count the beeps in each series. Record the digits below.
4. Turn the radio off.
NOTES: The radio pauses and emits a low tone at the end of each series of beeps, separating one digit from the next.
The radio emits a triple tone when the readout (beep out) process is complete.
CHANNEL 1:
1st
digit
# of beeps
in series
3. PRESS & RELEASE.
CHANNEL 2:
The radio will start
beeping rapidly.
5th
digit
# of beeps
in series
NOTES: 1. Ten (10) beeps = 0 (zero).
For assistance, call 800-USA-1-USA
Examples: 2 beeps = 2; 10 beeps = 0 (zero).
Frequency Code
2nd
Pause;
digit
radio emits
# of beeps
a low tone.
*
in series
Frequency Code
Pause; 6th
digit
radio emits
# of beeps
a low tone.
*
in series
2. The radio will beep out "44" as a tone code if it has been programmed for "No Tone."
3. A radio that was PC-programmed with any frequency not listed in Table 1, page 5, will emit
meaningless beeps on contents readout.
4. A radio with identical codes in both channels will beep out only one frequency and one QC code.
5. Ritron JMX/ SST radios can have a different Quiet Call tone programmed into each channel.
* The radio pauses to emit a low tone at the end of each beep series.
800-USA-1-USA 800-USA-1-USA 800-USA-1-USA 800-USA-1-USA (800-872-1872)
ANNEL 1:
Tone Code
3rd
Pause; Pause;
digit
radio emits radio emits
# of beeps
a low tone. a low tone.
*
in series
ANNEL 1:
Tone Code
Pause; 7th Pause;
digit
radio emits radio emits
# of beeps
a low tone. a low tone.
*
in series
4th
Pause;
digit
radio emits
# of beeps
a low tone.
* *
in series
8th Pause;
digit
radio emits
# of beeps
a low tone.
* *
in series