Advertisement
User Manual
MITSUMI WiFi Module
MODEL DWM-W016
The purpose of this manual is to explain correct way how to integrate module
DWM-W016 to the end product. It includes procedures that shall assist you to avoid
unforeseen problems. This manual presents information that shows how module and
OEM product, where module integrated, complies with regulations in certain regions. Any
modifications, not expressly approved by the manufacturer could void the authority to
operate in these regions.
The MITSUMI WiFi Module, model DWM-W016 has to be installed and used in accordance
with the technical description/installation instructions provided by the manufacturer.
For detail information concerning type approval of this module (e.g. where this module is
already pre-approved) please contact the authorized local distributor or the
manufacturer.
The system may only be implemented in the configuration that was authorized. Note that
any changes or modifications to this equipment not expressly approved by the
manufacturer could void the user's authority to operate this equipment.
Advertisement
Table of Contents
Related Manuals for Mitsumi DWM-W016
Summary of Contents for Mitsumi DWM-W016
- Page 1 MODEL DWM-W016 The purpose of this manual is to explain correct way how to integrate module DWM-W016 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions.
- Page 2 Regulatory Information Operational Information Wireless Interoperability The end product integrating this module is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards.
- Page 3 Labeling MITSUMI WiFi module DWM-W016 labelled as below. FCC ID: EW4DWMW016 The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: EW4DWMW016”...
- Page 4 device must not be co-located or operating in conjunction with any other antenna or transmitter.
- Page 5 Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device.
- Page 6 Europe-EU Declaration of Conformity and Restrictions Hereby, MITSUMI declares that this Mitsumi WiFi module DWM-W016 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the symbol and can be used throughout the European community.
- Page 7 Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
- Page 8 NCC Warning Statement 低功率電波輻性電機管理辦法 第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使 用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發 現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信 或工業、科學及醫療用電波輻射性電機設備之干擾。 Translation: Article 12 Without permission, any company, firm or user shall not alter the frequency, increase the power, or change the characteristics and functions of the original design of the certified lower power frequency electric machinery.
Need help?
Do you have a question about the DWM-W016 and is the answer not in the manual?
Questions and answers