1. Manuals
  2. Brands
  3. Digital Equipment Manuals
  4. Printer
  5. DEClaser 2100
  6. Installation manual

Digital Equipment DEClaser 2100 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DEClaser 2100 Printer
Installation Guide
EK–D2100–IN–001
Digital Equipment Corporation
Maynard, Massachusetts

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DEClaser 2100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Digital Equipment DEClaser 2100

Summary of Contents for Digital Equipment DEClaser 2100

  • Page 1 DEClaser 2100 Printer Installation Guide EK–D2100–IN–001 Digital Equipment Corporation Maynard, Massachusetts...
  • Page 2 Any software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license. No responsibility is assumed for the use or reliability of software or equipment that is not supplied by Digital Equipment Corporation or its affiliated companies.
  • Page 3 FCC NOTICE: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.

  • Page 4: Table Of Contents

    Printer Inventory ........2–1 DEClaser 2100 Printer ......2–2 Unpacking the Printer .
  • Page 5 Chapter 7 Verifying the Installation Checking the Printer Mechanism ..... . 7–1 7.1.1 Testing the Printer ....... 7–3 7.1.2 Producing a Test Print .

  • Page 6: Preface

    Preface The DEClaser 2100 printer is a nonimpact, desktop, page printer. This guide covers the installation of the DEClaser 2100 printer up to the point where it is certified to be operating properly. Intended Audience This guide is written for installers of the DEClaser 2100 printer.
  • Page 7 The documentation set consists of: • One DEClaser 2100 Printer Installation Guide • One DEClaser 2100 Printer Operator’s Guide • One spine insert for the binder • One 3-ring binder NOTE: You cannot order the installation or operator’s guide individually.
  • Page 8 The DEClaser 2100 printer complies with laser product performance standards set by government agencies as a Class 1 Laser Product. The DEClaser 2100 printer does not emit hazardous light, since the beam is totally enclosed during all modes of customer operation and maintenance.

  • Page 9: Chapter 1 Preparing Your Site

    Chapter 1 Preparing Your Site The performance of the DEClaser 2100 printer can be affected by electrical and environmental conditions surrounding its work location. This chapter lists the requirements for installing the DEClaser printer in a location where it performs best.

  • Page 10: Operating Location Requirements

    1.2 Operating Location Requirements The DEClaser 2100 printer should be installed in an area that meets the following requirements: • A flat, level surface free from vibrations. • Enough surrounding space to allow ventilation and easy access to all sides of the printer for servicing.

  • Page 11: Environmental Conditions

    1.3 Environmental Conditions For the proper operation of the printer, be certain the following environmental requirements are met: • Maintain the site within a temperature range of 10°C to 32.5°C (50°F to 91°F). • Maintain a humidity range of 20% to 80% (noncondensing). This ensures consistent image quality and prevents paper jams.

  • Page 12: Chapter 2 Unpacking Your Printer

    CAUTION: Damage will occur if the packing and spacers are not removed before turning on the printer. 2.1 Printer Inventory Your DEClaser 2100 printer and accessories come packed in two boxes. The following lists identify what items are in each box. The larger box contains: •...

  • Page 13: Declaser 2100 Printer

    2.2 DEClaser 2100 Printer The following illustration shows the front and rear views of the printer with the principal areas indicated. mlo-004347 2–2 DEClaser 2100 Printer Installation Guide...

  • Page 14: Unpacking The Printer

    2.3 Unpacking the Printer The instructions in this chapter begin at the point where the printer has been removed from the shipping box. 1. Remove the printer from the plastic bag. 2. Remove the packing tape and the packing cardboard from the paper cassette slot.
  • Page 15 3. Press the release button on the top of the printer and raise the printer cover to its most upright position. mlo-004349 4. Remove the packing foam inside the printer. mlo-004350 2–4 DEClaser 2100 Printer Installation Guide...
  • Page 16 5. Remove the two fixing assembly spacers. mlo-004352 6. Remove the top cover packing spacer. mlo-004351 Unpacking Your Printer 2–5...

  • Page 17: Chapter 3 Cleaning The Fixing Assembly Roller

    You replace the fixing assembly roller cleaner each time you replace the EP-S cartridge. A cleaner comes with each EP-S cartridge kit. Refer to the DEClaser 2100 Printer Operator’s Guide for instructions on how to replace the EP-S cartridge and the fixing assembly roller cleaner.
  • Page 18 2. Open the green fixing assembly cover. mlo-004354 3. Wipe the fixing roller with the felt pad on the end of the cleaner. mlo-004355 3–2 DEClaser 2100 Printer Installation Guide...
  • Page 19 4. Peel off the felt pad and discard it. mlo-004356 5. Insert the cleaner into the fixing assembly. mlo-004357 Cleaning the Fixing Assembly Roller 3–3...
  • Page 20 6. Close the fixing assembly cover. NOTE: The fixing assembly cover does not close tightly. mlo-004358 3–4 DEClaser 2100 Printer Installation Guide...

  • Page 21: Chapter 4 Installing The Ep-S Cartridge

    Chapter 4 Installing the EP-S Cartridge This chapter describes how to install the electrophotographic supplies (EP- S) cartridge. It is important to handle the EP-S cartridge properly. Be aware of these cautions when handling the EP-S cartridge. CAUTIONS: Do not slide the cartridge cover open. Do not stand the cartridge on end or place it upside down.
  • Page 22 1. Lower the top cover to its halfway position. mlo-004360 2. Remove the EP-S cartridge from its protective bag. mlo-004361 4–2 DEClaser 2100 Printer Installation Guide...
  • Page 23 3. Rock the EP-S cartridge five or six times as shown to distribute the toner evenly. mlo-004362 4. Install the EP-S cartridge. mlo-004363 Installing the EP-S Cartridge 4–3...
  • Page 24 Discard the sealing tape. NOTE: The sealing tape is about 55 cm (22") long and may have toner on it. If you get toner on your hands or clothing, wash with cold water and soap. mlo-004365 4–4 DEClaser 2100 Printer Installation Guide...
  • Page 25 7. Close the top cover by pushing down on the hand grip until the cover snaps into place. mlo-004366 Installing the EP-S Cartridge 4–5...

  • Page 26: Chapter 5 Loading Paper

    Loading Paper This chapter describes how to unpack the paper cassette and how to load paper into the DEClaser 2100 printer. The paper cassette holds about 200 sheets of 80 g/m (21 lb) paper. For further information about the kind of paper to use, refer to the DEClaser 2100 Printer Operator’s Guide.
  • Page 27 To prevent paper jams, do not place an excessive amount of paper into the tray. There should be a small amount of space between the paper and the maximum height guard. Make sure the paper lies perfectly flat in the tray. mlo-004378 5–2 DEClaser 2100 Printer Installation Guide...
  • Page 28 4. Replace the cassette cover on the paper tray. mlo-004369 5. Insert the paper cassette into the printer. mlo-004370 Loading Paper 5–3...

  • Page 29: Chapter 6 Connecting The Printer

    Chapter 6 Connecting the Printer This chapter describes how to connect your printer to the host device and to a power source. 6.1 Connecting to the Host Device Your printer is equipped with both a serial interface connector and a parallel interface connector.

  • Page 30: Serial Interface Connection

    2. Attach the H8571–E adapter, which came with your printer, to the serial port on the back of the printer. Use a flathead screwdriver or your fingers to secure the adapter to the printer. mlo-004372 6–2 DEClaser 2100 Printer Installation Guide...
  • Page 31 3. Plug the remaining end of the BC16E cable into the H8571–E adapter. mlo-004373 NOTE: Refer to Appendix A for information on host devices that do not accept the BC16E cable. Connecting the Printer 6–3...
  • Page 32 firmly into the host device. 2. Tighten the two screws. 3. Plug the other end of the BC19M–10 cable into the printer. 4. Secure the cable by pressing the clips over the sides of the connector. mlo-004374 6–4 DEClaser 2100 Printer Installation Guide...

  • Page 33: Connecting To A Power Source

    6.2 Connecting to a Power Source CAUTION: Be sure to check that the wall outlet voltage matches the voltage of your printer. Your electrician can make this determination for you if you do not know. The power cord receptacle and power switch are located at the rear of the printer.
  • Page 34 2. Plug the power cord into the power cord receptacle just below the power switch. mlo-004376 3. Insert the other end of the power cord into a power outlet. WARNING: Do not use an adapter plug on the power cord. 6–6 DEClaser 2100 Printer Installation Guide...

  • Page 35: Chapter 7 Verifying The Installation

    Chapter 7 Verifying the Installation This chapter describes how to check the printer mechanism and how to print a test page. 7.1 Checking the Printer Mechanism This section describes how to determine if the printer is running properly. 1. Press the power switch to the ON ( | ) position. mlo-004377 Verifying the Installation 7–1...
  • Page 36 Data indicators light, and 02 WARMING UP appears on the liquid crystal display (LCD). mlo-004378 When the printer warms up (about one minute), 00 READY DEC appears on the display, and the On Line and Ready indicators light. You are now ready to print. 7–2 DEClaser 2100 Printer Installation Guide...

  • Page 37: Testing The Printer

    7.1.1 Testing the Printer This section describes how to perform a printer self-test. The test page looks like the sample on the following page and only verifies that the printing mechanism is functioning properly. 1. Using a ballpoint pen or like instrument, press the self-test button located on the right side of the printer.
  • Page 38 — 15 ENGINE TEST appears on the LCD display, and a test image of vertical stripes prints. mlo-004380 7–4 DEClaser 2100 Printer Installation Guide...

  • Page 39: Producing A Test Print

    7.1.2 Producing a Test Print The following test shows that the printer, with the exception of the interface unit, is working properly. 1. Press to place the printer in the offline state. On Line 2. Press for 2 seconds. Test/Font —...

  • Page 40: Conclusion

    7.2 Conclusion This concludes the installation of your DEClaser 2100 printer. Refer to your DEClaser 2100 Printer Operator’s Guide for detailed instructions on features, maintenance, and troubleshooting. 7–6 DEClaser 2100 Printer Installation Guide...

  • Page 41: Appendix A Cabling Information

    NOTE: For a complete list of accessories and supplies and instructions on how to order them, refer to the DEClaser 2100 Printer Operator’s Guide. Table A–1: Cables and Adapters for Communication Connections Adapter and...
  • Page 42 BC16E cable to the H8571–D. Attach the H8571–E adapter to the DEClaser printer, then connect the other end of the BC16E cable to the H8571–E. H8571–E and BC16E (DECconnect cable) are included with the DEClaser 2100 printer. A–2 DEClaser 2100 Printer Installation Guide...
  • Page 43 BC16E cable to the H8571–E. European DECstations Parallel Port 200, 300, 350 Series BC19M–10 Connect the BC19M–10 to the DEClaser printer and to the host device. H8571–E and BC16E (DECconnect cable) are included with the DEClaser 2100 printer. Cabling Information A–3...
  • Page 44 BC16E cable to the H8571–E. The combination of the H8571–C adapter, the BC16E cable, and the H8571–E acts as a straight-through cable. H8571–E and BC16E (DECconnect cable) are included with the DEClaser 2100 printer. A–4 DEClaser 2100 Printer Installation Guide...

  • Page 45: Interface Programming Instructions

    NOTE: On IBM personal computers and compatibles, printer output is normally directed to LPT1, the first parallel port. 2. Connect the H8571–A adapter as described in Table A–1. 3. Refer to the DEClaser 2100 Printer Operator’s Guide for instructions on how to select DTR flow control. Cabling Information...

  • Page 46: Parallel Communication

    NOTE: On IBM personal computers and compatibles, printer output is normally directed to LPT1, the first parallel port. 2. Connect the H8571–A adapter as described in Table A–1. 3. Refer to the DEClaser 2100 Printer Operator’s Guide for instructions on how to select XON/XOFF. A.2.2 Parallel Communication...

Table of Contents