Table of Contents
Related Manuals for Haier HWT08AN1
Summary of Contents for Haier HWT08AN1
- Page 1 TOP LOAD FULL-AUTOMATIC WASHING MACHINE USER’S MANUAL MODEL HWT07AN1 HWT08AN1 HWT09AN1 HWT10AN1 HWT10ANB1 Please read this manual carefully before 0030517190 operating your washing machine and retain it for future reference.
-
Page 2: Table Of Contents
CONTENTS Product overview Safety precautions Description of symbols Safety Safety warnings Installation & adjustment Installing the bottom plate Balancing the washing machine Installation of the drain hose Installation of water inlet hoses Before washing Check the following before washing Operation Loading your laundry Loading detergent Explanation of the display... -
Page 3: Product Overview
Product overview Top lid Detergent tray Inner tub Outer tub cover Top deck Pulsator Cabinet Screw cover Base frame Adjustable feet (2 pieces) Control panel Cold water inlet valve Hot water inlet valve Hook Handle Power cord Back cover Drain hose connector Drain pump filter cap Fixed feet (2 pieces) (Not to be removed by... -
Page 4: Safety Precautions
... bed and breakfast type environments; ... areas for communal use in blocks of flats or in launderettes; ... max. capacity 7 kg (HWT07AN1), max. capacity 8 kg (HWT08AN1), max. capacity 9 kg (HWT09AN1), max. capacity 10 kg (HWT10AN1/HWT10ANB1), water pressure 0.03-1MPa. - Page 5 Safety precautions Forbidden Do not install this appliance in a Do not connect to hot damp or wet environment. Do not water higer than leave wet laundry on the Control 60°C temperature. Panel or spray water directly onto this appliance as this may cause the washer to malfunction or cause an electrical fault.
-
Page 6: Installation & Adjustment
Safety precautions If power cord or other parts of this machine become damaged or faulty, please contact a technician to have it repaired .. Do not attempt repairs by yourself as this may cause personal harm or void warranty. The new hose-sets supplied with the appliance are to be used and the old hose-sets should not be reused. -
Page 7: Balancing The Washing Machine
Installation & Adjustment Balancing the washing machine Installation on an uneven surface can lead to ‘out of balance’ events, instability in the machine operation, or even failure to successfully complete a wash cycle. Please refer to the following methods for adjustment: 1.Confirm whether the machine is level. -
Page 8: Installation Of Water Inlet Hoses
Installation & Adjustment Water inlet 1. Connect the cold hose (blue connector) to the cold tap and the hot hose (red connector) to the hot tap. You may have to use pliers to tighten the coupling. Do not over tighten as this may cause damage to the valve or hose fittings. -
Page 9: Before Washing
Before washing Preparation before washing 1.Connect the water inlet hose. Open the water faucet. 2.Insert the power plug into the wall power socket. 3.Ensure the drain hose is mounted at the correct height. 4.When the water pressure in the user's home is too low, it may not be able to wash detergents and softeners effectively (which may agglomerate). -
Page 10: Operation
Operation Loading your laundry The rated washing capacity refers to the largest dry weight of a load that can be washed. The thickness, size and type of clothes will influence the actual capacity. Do not select more than water level “Mid” for clothes less than 2.0kg, to avoid splashing of water. -
Page 11: Explanation Of The Display
Operation Explanation of buttons Auto High Favorite （Long） Extra High Spin Warm Soiled + Rinse Normal （Short） Soak Wash Cold No Spin Power Water Water Spin Rinse Options Progress Delay Level Temp （Speed） Cotton Express 30 Towels Delicate Sheets Wool Hygiene Synthetic Start/ Pause... - Page 12 Operation Digital display During the wash cycle, the digital display will show the time remaining in minutes. Page 16 If an issue occurs, the display will show a user warning or error code (see to page 16) If a ‘Delay start’ is selected, the display will show the total time to cycle completion including the delay period, in hours A "Power"...
- Page 13 Spin is suitable for HWT07AN1 model, press Spin button to choose spin time in “Short” Spin “Med” “Long”. &Spin Spin Speed is suitable for HWT08AN1/HWT09AN1/HWT10AN1/HWT10ANB1 model, Speed press Spin speed button to choose spin speed in “Low” “Med” “High”. No Spin The machine will drain water out.
- Page 14 Operation F "Options" button Soak This cycle consists of a ½ agitate time then complete 2hr soak (with interm-- ittent agitates during soak) , After soak period, continue with the second ½ of agitate phase. Soak is available on all cycles except Wool and Express cycles. Soiled+ This cycle consists a 15 minute soak sequence ½...
-
Page 15: Operation And Wash Cycles
Operation and Wash Cycles Press the button to switch power on/off Turn the knob to select automatic program After the power is turned on, the default is Mixed program. Then rotate the knob to select other programs. For example, when you want to wash light dirty clothes quickl , use a Express procedure. - Page 16 For HWT07AN 1model Water Level High, Water Temp Warm, Rinse Eco, Spin Long, Options Soiled+&Soak. For HWT08AN1, HWT09AN1, HWT10AN1, HWT10ANB1 model. Water Level High, Water Temp Warm, Rinse Eco, Spin Speed High, Options Soiled+&Soak Please use low suds/high efficiency detergent.
-
Page 17: Cleaning And Maintenance
Cleaning and Maintenance Maintenance Remove the power plug before carrying out any cleaning or maintenance. Clean the lint filter(s) and detergent box after each wash, otherwise it may influence you using the machine. Both lint filters must be used during Clean the detergent box and set it on the washing. -
Page 18: Trouble-Shooting
Trouble-shooting If there is a fault or the machine does not operate correctly, remove the power plug before checking the machine. Using diagnostic list below, please check if the machine requires a repair. If a repair is required, please contact our customer care team, do not try to fix it by yourself. -
Page 19: Packing List
Trouble-shooting Problem Possible causes What to do The display shows FA The water level sensor has failed. Please contact Customer Care. The display shows F2. Overflow Error Please contact Customer Care. The display shows E2-1. The door lock alarm Please contact Customer Care. The display shows FC1. -
Page 20: Specification
W 610 D 620 H 1045 Water inlet pressure 0.03MPa-1.0MPa 0.03MPa-1.0MPa Rated Washing capacity 10kg Type TOP LOAD FULL-AUTOMATIC WASHING MACHINE HWT09AN1 Model HWT08AN1 Rated voltage/frequency 220-240V/50Hz 220-240V/50Hz Rated washing power 470W 470W Rated spinning power 300W 300W Net weight...