Advertisement
ADDITIONAL BATTERY SAFETY RULES
To reduce the risk of fire,
WARNING
personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fluid or allow a fluid
to flow inside them. Corrosive or conductive fluids,
such as seawater, certain industrial chemicals, and
bleach or bleach-containing products, etc., can
cause a short circuit.
WARNING
Do
non-rechargeable batteries.
SPECIFICATIONS
Cat. No. ...............M12FRAIWF38, M12FRAIWF12
RPM ............................................................. 0-3000
IPM .............................................................. 0-3600
Volts............................................................ 12V DC
Battery Type ................................................. M12™
Charger Type................................................ M12™
Recommended Ambient
Operating Temperature ....................-17°C to 51°C
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Attaching and Removing Accessories
3/8" and 1/2" Friction Ring
(Cat. No. M12FRAIWF38 and M12FRAIWF12)
1. Use only the appropriate size Square Drive Sockets.
2. To attach a socket, align the accessory with the
anvil and push it firmly over the retaining ring.
3. To remove the accessory, pull the accessory o
the anvil.
OPERATION
To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an appro-
priate dust extraction solution.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash in an alternating pattern and the tool will not
run. Allow the battery to cool down.
not
charge
4
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Push for
Forward
PUSH TO CENTRE TO LOCK
1. For forward (clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
2. For reverse (counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
3. To lock the trigger, push the control switch to the
centre position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance, changing accessories, storing the tool
and any time the tool is not in use.
Using the Drive Control
The drive control button is used
to adjust the rotation speed
(RPM) for the application.
To select the drive control
mode:
1. Unlock, then pull and
release the trigger to turn
on the tool. The current in-
dicator is lit. NOTE: The
trigger will not work when
the control switch is in the
locked position.
2. Press the drive control button
the 4 modes. When the desired mode indicator is
lit, begin work.
3. In
mode:
• Auto Shut O - In forward,
the tool runs at a reduced
RPM and then shuts o
o n c e t h e t o r q u e i s
achieved.
• Bolt Removal - In reverse,
the tool runs at full RPM
and IPM until the nut breaks free from the joint.
Then, the tool slows to a reduced RPM for better
control in removing the nut.
Starting, Stopping and Controlling Speed
These tools may be operated at any speed from 0
to full speed.
1. To start the tool, pull the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2. To vary the driving speed, simply increase or
decrease pressure on the trigger. The further the
trigger is pulled, the greater the speed.
3. To stop the tool, release the trigger and the electric
brake stops the tool instantly.
Push for
Reverse
Drive Control
to cycle through
Mode
RPM
IPM
1
0-1550 0-1350
2
0-2300 0-2700
3
0-3000 0-3600
0-3000* 0-3600*
Advertisement
