Configuring The Device Overall (System Settings); Parameter List - Boss ME-90 Reference Manual

Configuring the device overall (system settings)

1 .
Press the [MEMORY/MANUAL] pedal to switch to
manual mode (p. 6).
2 .
Press the [EDIT] button to select the parameter to
set.
The parameter to set changes each time you press the [EDIT]
button.
Use the [BANK É] [BANK Ç] pedals to select a
3 .
value.
4 .
Press the [WRITE] button.
The settings are saved.

Parameter list

Parameter Display
OUTPUT SELECT
1–12
n0
Knob motion
n1
USB LEVEL
L0–L9
d0
USB DIRECT MONITOR
* Power-on setting
is d1
d1
b0
USB LOOPBACK
b1
c1–c9,
MIDI channels
c. 0 –c. 6
t0
Output settings when
using the tuner
t1
16
Explanation
Specifies the amp that's connected
to the OUTPUT jacks.
* For details on the amp types,
refer to the "ME-90 Parameter
Guide" (Roland website).
The parameter value changes
instantly when you operate the
knobs (this is the factory setting).
The value only changes once
the knob position reaches the
parameter's current value.
Adjusts the level of audio input
from your computer, which is
mixed with the sound that passes
through the ME-90's effects.
The sound of the ME-90 is not
output to the PHONES jack and the
OUTPUT jacks.
The sound of the ME-90 is output
to the PHONES jack and the
OUTPUT jacks.
The input audio from the computer
is not output via USB OUT.
The input audio from the computer
is output via USB OUT.
Ch 1–ch 9, ch 10–ch 16
No audio is output when you're
using the tuner.
The direct sound is output while
you're using the tuner.
Parameter Display
H0
Bank switch operation
H1
m0
Switching to manual
mode
m1
S0
SEND/RETURN
insertion point
setting
S1
o0
Preserving/muting
the tail of an effect
when switching
between patches or
turning effects off
o1
E0
LED illumination color
E1
r0
REV footswitch
functions
r1
Explanation
Pressing the bank pedal to switch
banks only changes the bank
shown in the display, without
actually switching to a different
patch. Both the bank and number
are confirmed right when you press
a numbered pedal, and the unit
switches to the next patch. (Factory
settings)
The patch switches instantly when
a bank pedal or numbered pedal is
pressed.
When you switch from memory
mode to manual mode, the current
knob settings are applied to the
sound.
When you switch from memory
mode to manual mode, the
memory settings are carried over
(factory setting).
SEND/RETURN are inserted before
the preamp in the signal chain. This
is the optimal setting when using a
distortion pedal or the like (factory
setting).
SEND/RETURN are inserted after
the preamp in the signal chain. This
is the optimal setting when using a
delay pedal or the like.
When you switch patches, the
effect's delay sound you selected in
DELAY is not carried over. This does
not apply to the DELAY for EQ/FX2
and MOD.
When you switch patches, the
effect's delay sound you selected
in DELAY is carried over (factory
setting). This does not apply to the
DELAY for EQ/FX2 and MOD.
The LEDs can light up in one of ten
colors (factory setting).
The LEDs only light up to indicate
their state in white and in
color changes that are easy to
distinguish (only red, yellow and
blue).
This mode is intended for users
with color blindness and other
vision deficiencies and may be
generally preferred by those
who like a more classic display
appearance.
In manual mode, this turns the
reverb on/off (factory setting).
In manual mode, this turns SEND/
RETURN on/off.