Related Manuals for Quest Engineering PR-130BT
Summary of Contents for Quest Engineering PR-130BT
- Page 1 COMMERCIAL MIXER-AMPLIFIER MODEL: PR-130BT / PR-240BT Specifications are subject to change without notice...
- Page 2 PR-130BT / PR-240BT IMPORTANT SAFETY INSTRUCTIONS Read these instructions - All the safety and operating instructions should be The apparatus has been damaged in any way, such as power supply read before this product is operated. cord or plug is damaged, liquid has been spilled or objects have fallen Keep these instructions –...
-
Page 3: Table Of Contents
PR-130BT / PR-240BT Table of Contents Introduction Features Controls Setup Connections 10-13 Operations 14-16 Specifications 21000 Transcanadienne Baie d’Urfé, Québec, H9X 4B7 Phone: 1-877-374-5266 Fax: 888-918-2244 www.eriksoncommercial.com Copyright © 2022 Exer�s | Jam. All rights reserved – 3 –... -
Page 4: Introduction
These models have a constant voltage power amplifier allowing use at 70/100V or at low impedance of 4 Ohms. The PR-130BT can deliver a power of 130 Watts, and the PR-240BT a power of 240 Watts. They offer six inputs channels (terminal block/RCA) with independent level controls to facilitate the connection of sound sources. -
Page 5: Features
PR-130BT / PR-240BT Features The PR-130BT and PR-240BT mixer-amplifiers are complete all-in-one mixer-amplifier solutions for commercial and industrial applications. These low-cost units offer all the necessary features in a simple format. • 4 Balanced Mic/Line Inputs, with 48V Phantom. • 2 Aux In, 1 Line Out, and 1 Link Out, all on RCA connectors. -
Page 6: Controls
PR-130BT / PR-240BT Controls FRONT PANEL [Figure 1.1 Front panel diagram] 1. BMP-1 Bluetooth Media Player. 2. Speaker zone output selector and indicator. 3. Output Volume Control for each zone. 4. Status indicators ( Protect/Output level/AC power ). 5. Power switch. - Page 7 PR-130BT / PR-240BT REAR PANEL [Figure 1.2 Rear panel diagram] 1. AC 120 V 50/60Hz with fuse. 2. Speaker outputs connector ( individual zone and 100V, 4-ohm, 70V output ). 3. FM antenna, line output of media module and remote mic station (RM6) input jack.
-
Page 8: Setup
Location: Take the unit out of its packaging (keep it for any return to the workshop). The PR-130BT and PR-240BT mixing amplifiers can be installed in a standard 19” equipment rack or on a shelf. To install the unit in a standard 19”... - Page 9 A simple way to represent a constant voltage is to divide the power in Watts of the amplifier by the number of loudspeakers used. For example, to connect ten loudspeakers to the output of a PR-130BT amplifier, use a loudspeaker whose transformer provides a tap point of approximately 10 Watts.
-
Page 10: Connections
PR-130BT / PR-240BT Connections Connecting speakers Connect the speakers to the terminal block output connectors on the rear. Never turn on the amplifier when the speakers are not connected to the outputs. When using the 4 Ohm output, you must connect speakers with a minimum impedance of 4 Ohms (4 Ohms or more). - Page 11 PR-130BT / PR-240BT Connecting sound sources Then connect the sound sources to the terminal block input connectors on the back. If your console or source has Balanced outputs, use balanced three-conductor connections and connectors (you can use unbalanced connections, but you'll get better sound quality and less noise if you use balanced connections).
- Page 12 PR-130BT / PR-240BT Wiring guide Choose the input connector and the appropriate cable for each source. We recommend the use of pre-assembled or professionally assembled 22-to-24-gauge balanced cables. Figure 2.1 shows the connection diagrams for the different connectors. RCA input connectors can also be used as unbalanced inputs.
- Page 13 PR-130BT / PR-240BT Wiring guide - Continued CAUTION: Never use shielded cable for speaker output. Maintain correct polarity on output connectors. For each output channel, connect the output terminal block connector to the speakers. Use terminals marked COM and 4Ω / 8Ω for low impedance speakers, or use terminals marked 70V or 100V, and COM for high impedance speakers.
-
Page 14: Operations
PR-130BT / PR-240BT Operations Signal input gain control The PR-Series mixer-amplifiers can accept balanced mic or line input signals, thanks to the gain selec�on switches (figure 3.1). Phantom power The PR-Series mixer-amplifiers can supply 48V DC phantom power to use condenser microphones on any of the mic channels. - Page 15 PR-130BT / PR-240BT Remote Microphone A RM6 remote paging microphone station can be connected to the PR-Series mixer-amplifiers. The RM6 remote microphone station can select from the 6 individual zones and play a pre-announcement chime. The RM6 remote microphone station should be connected using UTP CAT5/6, CAT6 is recommended for longer distance.
- Page 16 PR-130BT / PR-240BT Using the TELE-Paging func�on Expanding The PR-Series public address amplifiers using the LINK OUT or REC OUT mixer- equipment. [Figure 3.6] Output Zone Selector and Volume Controls The PR-Series mixer-amplifiers feature a 6-Zone output selector, each zone with a dedicated 6-steps a�enuator.
- Page 17 PR-130BT / PR-240BT BPM-1 Media Player MENU AUX IN 100mA MP3 Player - Tuner - Bluetooth 1. Display 2. USB Connector 3. SD Card Slot 4. MENU Button Short press to select FM/USB/SD card/Blue Tooth/AUX. Press and hold to turn the module on and off.
- Page 18 PR-130BT / PR-240BT Using the Tuner 1. Press MODE key until the display shows “Radio” 2. Press PLAY / PAUSE key to select radio 3. Press and hold NEXT or PREVIOUS key to automatically seek the previous or next available FM station 4.
-
Page 19: Specifications
PR-130BT / PR-240BT Specifications: Performance Model Number PR-130BT PR-240BT Frequency Response at 1watt from speaker out tap, 100Hz~10kHz +1.5 / -3 dB Tone Control, 100Hz,10KHz ±12dB ±3dB Signal to Noise Ratio at rated power output Less than 90dB Crosstalk at all control maximum -70dB at 1kHz Rated Output Power at THD 0.5%... - Page 20 21000 Transcanadienne Baie d’Urfé, Québec, H9X 4B7 Phone: 1-877-374-5266 Fax: 888-918-2244 www.eriksoncommercial.com Copyright © 2022 Exer�s | Jam. All rights reserved...