Related Manuals for WoodFast PT410A
Summary of Contents for WoodFast PT410A
- Page 1 Instruction Manual Planer & Thicknesser PT410A IMPORTANT For your safety read instructions carefully before assembling or using this product. Original Instruction Save this manual for V.1-201910 future reference.
- Page 2 Index GENERAL INFORMATION 1.1 Foreword MACHINE DESCRIPTION Machine identification Getting to know your machine Technical specification Recommended protective clothing Noise emission Prescribed use of the machine Hazards Safety instructions for planer/thicknesser INSTALLATION Lifting and unloading Position of the machine Identifying shipping boxes Installations of loose parts 3.4.1 Fence installation 3.4.2 Switch installation...
-
Page 3: General Information
1. General Information FOREWORD This manual must be read and understood before operating the machine. This will provide a better working knowledge of the machine, for increased safety and to obtain the best results. 2. Machine Description MACHINE IDENTIFICATION There is a metallic identification plate fixed to the machine, containing the manufacturer's data, year of construction, serial number. GETTING TO KNOW YOUR MACHINE Sheet PT410A2216S4053... -
Page 4: Technical Specification
2.3 TECHNICAL SPECIFICATION SPECIFICATION PT410A Feed speed m/min Cutterblock speed rpm 5000 Cutterblock diameter mm Max thicknesser capacity mm 405x225 Max planing width mm Max depth of cut thicknesser mm Max depth of cut planer mm Knives pcs Fence tilting degree... - Page 5 2.8 SAFETY INSTRUCTIONS FOR PLANER.THICKNESSER A planer/thicknesser is a tool which can, due to operator carelessness, cause serious personal injury. It is therefore strongly recommended you read and observe: · these instructions, particularly the special safety information in the respective chapters; ·...
-
Page 6: Installation
3. Installation 3.1. LIFTING AND UNLOADING The machine can be transported by two means: - with a forklift truck. To do so, the machine is secured on a pallet with four hex bolts. - by several persons. Here, the machine is carried by means of carrying straps or two battens (A, Fig.1) placed underneath the thicknesser bed. -
Page 7: Electrical Connection
3.4. INSTALLATIONS OF LOOSE PARTS 3.4.1 SWITCH - INSTALLATION - Fit the switch (G, Fig.4) onto the bracket with two hex nuts. Sheet Sheet PT410A2216S4053 16寸平压刨 JL43070000 刨刀护板组件 FIG. 4 3.4.2 Cutterblock guard - INSTALLATION - Take off both of the hex socket screws (A, Fig.5). Install the cutterblock guard assembly (B, Fig.5) using two of hex socket screws. -
Page 8: Dust Chute - Installation
3.6. DUST CHUTE - INSTALLATION The dust chute complete with suction connector must be installed for thickness planing. CAUTION: The contact pins on the shaft of the dust chute (A, Fig. 6) must engage properly in the limit switch. Incorrectly installed dust chute the machine will not start. -
Page 9: Operating Procedures
PT410A2216S4053 16寸平压刨 5. Operating Procedures 5.1. ON/OFF SWITCH (Fig.10) · To switch ON = press green switch button. · To switch OFF = close cover or press red switch button. · To unlock the switch cover push the pin on the stop cover. e-stop FIG. -
Page 10: Thickness Planer Mode
- Planing the face of a plank or workpieces up to 75 mm thick: lower cutterblock cover from top onto workpiece. Adjust cutterblock cover so that the undermentioned distances are not exceeded in any position: rear edge (A, Fig.14) – workpiece max. 3 mm; front edge (B, Fig.14) –... -
Page 11: Maintenance
6. Maintenance 6.1 REPLACING CUTTER KNIVES CAUTION! Risk of personal injury by cuts from the cutter knives! Wear gloves when changing cutter knives. To remove the cutter knives: 1. Unplug power cable. 2. Push fence back. 3. Raise cutterblock cover fully and pull extrusion fully outwards. 4. - Page 12 Sheet PT410A2216S4053 16寸平压刨 6.2 Drive Belt Check The cutterblock drive belt and the feedgear drive belt need to be checked periodically and retightened if necessary. Both drive belts are located behind the machine's side panel. Checking the drive belt: 1. Unplug power cable. 2.