Page 2
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
Table of contents Preface ..............................5 Description of the device ......................... 9 Software installation ..........................11 Installing the driver ........................11 Installing the "SIMATIC NET PC Software" ................11 Uninstalling the "SIMATIC NET PC Software"................ 12 Hardware installation ..........................13 Configuration ............................
Updated operating instructions on the Internet You will find the current version of these operating instructions on the Product Support pages under the following entry ID: 62611661 (https://support.industry.siemens.com/cs/ww/en/view/62611661) Further documentation The documents listed below contain more detailed information on commissioning and using the communications processor.
Page 6
CP 5622 Industry Online Support In addition to the product documentation, the comprehensive online information platform of Siemens Industry Online Support at the following Internet address: Link: (https://support.industry.siemens.com/cs/de/en/) Apart from news, there you will also find: ● Project information: Manuals, FAQs, downloads, application examples etc.
Page 7
In order to protect plants, systems, machines and networks against cyber threats, it is necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial security concept. Siemens’ products and solutions only form one element of such a concept. Customer is responsible to prevent unauthorized access to its plants, systems, machines and networks.
● Own processor on the CP 1613 A2 relieves the PC/PG CPU ● Autosensing, autonegotiation ● The changeover between the AUI and ITP connector is made automatically by the CP 1613 A2 if you use Siemens ITP cables. ● ISO and TCP/IP transport protocol onboard Hardware requirements The CP 1613 A2 requires a PCI slot for operation.
Page 10
Description of the device CP 1613 A2 Operating Instructions, 08/2016, C79000-G8976-C303-02...
Install the software as described in the installation manual "SIMATIC NET PC Software". You will find this installation manual on the Product Support pages under the following entry 77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602) You should also note the current information on the "SIMATIC NET PC Software" on the Product Support pages in: Hotspot-Text (https://support.industry.siemens.com/cs/ww/en/ps/15362/pm)
Uninstall the entire software package as described and recommended in the installation manual "SIMATIC NET PC Software". You will find the installation manual on the "SIMATIC NET PC Software" DVD or on the Product Support pages under the following entry ID: 77377602 (https://support.industry.siemens.com/cs/ww/en/view/77377602) CP 1613 A2 Operating Instructions, 08/2016, C79000-G8976-C303-02...
Hardware installation Number of permitted communications processors Note A maximum of four CP 1613 A2 modules can be operated in a PC/PG at the same time. Take into account the technical specifications of the power supply for the PCI slots of the PG/PC.
Page 14
Further notes on passive network components You will find important notes on the use of passive network components in the document "Industrial Ethernet / PROFINET Passive Network Components (https://support.industry.siemens.com/cs/ww/en/view/84922825)". Procedure To install and connect up the communications processor follow the steps outlined below:...
Configuration Configuring To be able to configure the communications processor, the following engineering or configuration tools are available: ● STEP 7 V5.5 ● STEP 7 Professional (TIA Portal) ● Communication Settings (COML S7) The steps involved are described in the "Commissioning PC Stations" manual or in the relevant online helps.
Declaration of conformity You will find the declaration of conformity for this communications processor on the Product Support pages under the following entry ID: 58826997 (https://support.industry.siemens.com/cs/ww/en/view/58826997) C-TICK approval The communications processor meets the requirements of the Australian AS/NZS 3548 standard according to EN 61000-6-3.
Page 20
● Consult the dealer or an experienced radio/TV technician for help. Siemens AG is not responsible for any radio television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Siemens AG. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.