Specifications; Ec Declaration Of Conformity; Specific Safety Rules - Makita UH6580 Instruction Manual

ENGLISH
1-1. Switch trigger B
1-2. Switch trigger A
1-3. Switch trigger C
5-1. Hook complete
5-2. Tool's cord
5-3. Extension cord
6-1. Holder
6-2. Cord
7-1. Holder
7-2. Arm cord hook
11-1. Trimming direction
11-2. Tilt the blades
11-3. Hedge surface to be trimmed

SPECIFICATIONS

Strokes per minute (min
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for trimming hedges.
EC-DECLARATION OF CONFORMITY
The undersigned, Kato, as authorized by, declare that
the MAKITA machines,
TYPE:
UH5580,UH6580,UH7580
complies with the
requirements of the pertinent EU guidelines:
EU machinery guideline 98/37/EC, Noise emission
2000/14/EG, EU EMC guideline 2004/108/EC.
The requirements of the above EU guidelines were
implemented chiefly on the basis of the following
standards: EN60745-2-15, EN 55014, EN61000. The
conformity assessment procedure 2000/14/EG was
performed per Annex V. The measured sound pressure
level (LpA): is 86.5 dB(A). The measured sound power
level (Lwa) is 94.5 dB(A). The guaranteed sound power
level (Ld) is 96 dB(A). Uncertainty (K) is 0.7 dB(A).
Vibration
The vibration total
determined according to EN60745-2-15:
Vibration emission (ah, D): 4.4 m/s
Uncertainty (K): 1.5 m/s
Tomoyasu Kato CE2008
000230
Explanation of general view
16-1. Press
16-2. Chip receiver
16-3. Nut
16-4. Shear blade
17-1. Nut
17-2. Branch catcher
18-1. Hooks
18-2. Fit the hooks into groove
18-3. Grooves
19-1. Press the hooks on both sides
19-2. Unlock the hooks
20-1. Screws
20-2. Blade cover
Model
Blade length
-1
)
Overall length
Net weight
Safety class
standard safety and
value (tri-axial vector
2
2
UH5580
550 mm
1,500
970 mm
4.2 kg
ENE014-1
Responsible Manufacturer:
Makita Corporation
ENH020-1
3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN
Authorized Representative in Europe:
Makita International Europe Ltd.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
health

SPECIFIC SAFETY RULES

1. DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict
adherence to grinder safety rules. If you use
this tool unsafely or incorrectly, you can suffer
serious personal injury.
2. Keep all parts of the body away from the cutter
blade. Do not remove cut material or hold
material to be cut when blades are moving.
Make sure the switch is off when clearing
jammed material. A moment of inattention while
operating the hedge trimmer may result in serious
sum) personal injury.
3. Carry the hedge trimmer by the handle with
the cutter blade stopped. When transporting
or storing the hedge trimmer always fit the
cutting device cover. Proper handling of the
hedge trimmer will reduce possible personal injury
from the cutter blades.
5
21-1. Under cover
21-2. Blade cover
22-1. Gear housing cover
23-1. Crank
24-1. Screws
24-2. Shear blade
25-1. Crank
26-1. Ellipse of shear blade
28-1. Ellipse of shear blade
28-2. Crank
29-1. Crank
UH6580
650 mm
1,500
1,049 mm 1,157 mm
4.3 kg
/II
Director
UH7580
750 mm
1,500
4.4 kg
GEB041-1