Table of Contents
Advertisement
SuperWorkstation 5039D-I User's Manual
1.5 Motherboard Layout
Below is a layout with jumper, connector and LED locations shown. See the table on the
following page for descriptions. For detailed descriptions, pinout information and jumper
settings, refer to Chapter 5.
JUIDB1
VGA
LE1
VGA
LE1
JUIDB1
JOH1
LEDBMC
BMC
LED BMC
JIPMB1
JPL2
JPG1
JPL2
JBR1
JPB1
JPME2
X11SSM(-F)/X11SSL(-F)
REV:1.01
JI2C1
JI2C2
Designed in the USA
JD1
SP1
SP1
BT1
USB2/3
USB2/3
JL1
JL1
JBT1
BT1
JBT1
Intel PCH
JTPM1
JWD1
USB4/5
JSTBY1
I-SATA7
JSD1
I-SGPIO1
USB10
JF1
USB10(3.0)
I-SATA5
LED PWR
I-SATA4
LEDPWR
I-SATA3
I-SATA2
I-SATA2
FANA FAN3
JF1
FAN3
JSD2
USB8/9
FANA
I-SATA1
I- SATA0
I-SGPIO2
Figure 1-4. Motherboard Layout
Notes:
" " indicates the location of pin 1.
Jumpers/LED indicators not indicated are used for test purposes only.
The COM2, PCI-E Slot 4, I-SATA6 and I-SATA 7 ports shown above are not included on the
X11SSL-F.
IPMI_LAN
LAN1
USB0/1
COM1
LAN2
USB6/7
LAN2
LAN1
USB6/7
USB0/1
(3.0)
COM1
FAN4
IPMI_LAN
JPL1
JPL1
MAC CODE
JPI2C1
JPWR2
CPU
JPWR1
FAN2 FAN1
FAN2
FAN1
12
Quick Reference Table
Jumper
Description
JI
2
C1/JI
2
C2
SMB to PCI Slots Enable/Disable
JBR1
BIOS Recovery
JBT1
Clear CMOS
JPB1
BMC Enable/Disable
JPG1
VGA Enable/Disable
JPL1/JPL2
LAN1/LAN2 Enable/Disable
JPME2
Manufacturing Mode Select
JWD1
Watch Dog
LED
Description
LE1
Rear UID LED
LEDBMC
BMC Heartbeat LED
LEDPWR
Onboard Power LED
Connector
Description
BT1
Onboard Battery
COM1
COM1 (Serial Port) Header
Fan1-Fan4, FanA
System/CPU Fan Headers
(IPMI) LAN
Dedicated IPMI (RJ45) Port
I-SATA0-I-SATA5
(Intel PCH) SATA (Serial ATA) 3.0 Ports
I-SGPIO 1/2
Serial Link General Purpose I/O Headers
JD1
Speaker/Power LED Indicator
JF1
Front Panel Control Header
JIPMB1
4-pin External BMC I2C Header (for an IPMI Card)
JL1
Chassis Intrusion Header
JPI
2
C1
Power System Management Bus (Power SMB)
JOH1
Overheat LED Indicator
JPWR1
24-pin ATX Main Power Connector (Required Connection)
JPWR2
+12V 8-pin Power Connector
JSD1/JSD2
SATA DOM (Device On Module) Power Connectors
JSTBY1
Inject External P5V Standby Power
JTPM1
Trusted Platform Module/Port 80 Connector
JUIDB1
Unit Identifier Switch
LAN1/LAN2
Gigabit (RJ45) Ports
PCI-E (CPU) Slot 7
PCI-Express 3.0 x8 Slot
PCI-E (CPU) Slot 6
PCI-Express 3.0 x8 in x16 Slot
Table continued on next page.
13
Chapter 1: Introduction
Default Setting
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
Open (Normal)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Enabled)
Pins 1-2 (Normal)
Pins 1-2 (Reset)
Status
Blue: On; Unit Identified
Green: Blinking; BMC Normal
Green: Sollid On; Power On
Advertisement
Table of Contents
