Table of Contents
Advertisement
<Reference> EMG display of FDP display mode
(1) Transmit the code "59" from the Jig RCU.
The FDP shows the EMG content in the form of "E:**:**".
<Example 1>
E : 01 : 03
<Example 2>
E : - - : - -
(2) Transmit the code "59" from the Jig RCU again.
The FDP shows the EMG detail information <1> in the form
of " *1: *2 : 34 ".
*1 : Deck operation mode at the moment of EMG
*2 : Mechanism operation mode at the moment of EMG
3– : Mechanism sensor information at the moment of EMG
–4 : Mechanism mode position at the moment of EMG
(3) Transmit the code "59" from the Jig RCU once again.
The FDP shows the EMG detail information <2> in the form
of " *5 : *6 : *7 ".
*5 : Type of the cassette tape in use <1> .
*6 : Winding position of the cassette tape in use
*7 : Type of the cassette tape in use <2> (Winding area)
(4) Transmit the code "59" from the Jig RCU once again.
The FDP shows the EMG detail information <3> in the form
of "*8 : *9 : *10".
*8 : Previous deck operation mode at the moment of EMG
*9 : The deck operation mode of the one before the last at
the moment of EMG
*10: The deck operation mode of the one prior to one
above at the moment of EMG
(5) Transmit the code "59" from the Jig RCU once again to re-
set the display.
2.3.3 Clearing the EMG history
(1) Display the EMG history.
(2) Transmit the code "36" from the Jig RCU.
(3) Reset the EMG display.
Previous EMG
Latest EMG
No EMG record
2.3.4 Details of the OSD display in the EMG display mode
During the EMG display, the OSD shows the data on the deck
mode, etc. The details of the display contents are as follows.
Notes:
• The display is variable depending on the part No. of the
System Control microcomputer (IC3001) built into the
VCR. In the following, refer to the figure carrying the
same two characters as the top two characters of the
part number of your IC.
• The sensor information in the OSD display contents is
partially different from the mechanism sensor informa-
tion in EMG detail information <1>.
[For MN* only]
AA
BB
FF
GG
KK
L L
PP
QQ
UU
VV
AA : Deck operation mode (See EMG detail information <1>.)
BB : Mechanism operation mode
(See EMG detail of information <1>.)
CC : Mechanism transition flag
DD : Capstan motor control status
EE : Loading motor control status
FF
: Sensor information (See sensor information details.)
GG : Capstan motor speed
HH : Key code (JVC code)
I I
: Supply reel winding diameter data, higher 8 bits.
JJ
: Supply reel winding diameter data, lower 8 bits.
KK : Mechanism sensor information & mechanism mode posi-
tion(See EMG detail of information <1>.)
LL
: Tape speed data, higher 8 bits.
MM : Tape speed data, lower 8 bits.
NN : Cassette tape type <2>, higher 8 bits.
(See EMG detail of information <2>.)
OO : Cassette tape type <2>, lower 8 bits.
(See EMG detail of information <2>.)
PP : General data display area
YY: General data display area
*FF:Sensor information details
<Display>
** h
*
*
*
*
*
Encoder data
(See Mechanism mode sequence.)
Cassette tab present = 1
Cassette tab broken = 0
Cassette absent = 1
Cassette present = 0
Start sensor
End sensor
HR-J692US
HR-J692UC
CC
DD
EE
HH
I I
J J
MM
NN
OO
RR
SS
TT
WW
XX
YY
*
*
*
(No.82952)1-9
Advertisement
Table of Contents
