Related Manuals for AGF COLLECTANDRAIN 5400B
Summary of Contents for AGF COLLECTANDRAIN 5400B
- Page 1 Model 5400 Owner’s Manual Owner’s Manual Owner’s Manual Owner’s Manual for Models with Serial Number 5400-1000 and Higher www.agfmfg.com...
-
Page 2: Table Of Contents
Operating Instructions ..............7-8 Maintenance Instructions ............9-11 Verify Alarm Operation ..............9-10 Heater Operation ................9 Changing Timer Setting ..............10 Changing Thermostat Setting ........... 10-11 Maintenance Log ................11 AGF Manufacturing 100 Quaker Lane • Malvern, PA 19355 Phone: 610-240-4900 Fax: 610-240-4906 www.agfmfg.com... - Page 3 The M5400 maintains a comfortable temperature above freezing while minimizing power consumption. CAUTION: The heater and its deflector bracket may be hot. Use care when accessing the main cabinet for any reason. www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •...
-
Page 4: Model 5400
3. Confirm that the Supply Valve (upper valve) is in the open position (vertical) and ready to collect condensation, the Drain Valve (lower valve) is in the closed position (horizontal), and the pipe cap is tight. www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •... -
Page 5: Wiring
2. Connect one wire to the AC1 (auxiliary contact) Terminal. 3. Connect the other wire to the AC2 (auxiliary contact) Terminal. 4. Connect these wires to the appropriate place in the Remote Panel. www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •... -
Page 6: Verify Correct Operation
4. Turn the top dial of the Timer counter-clockwise from the 10h to the 10s band. The leg of the cross with the arrow (highlighted in red) points to the band. www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •... -
Page 7: Operating Instructions
The factory default setting of 60º F is suitable for conditions down to 0º F. Consult with AGF for recommended settings if operating the M5400 in areas below 0º F. The thermostat controls the heater operation to within approximately ± 10º F of the set-point (i.e. - Page 8 DRAIN additional water to accumulate. 7. Repeat the process until all of the accumulated water has been drained. 8. Once all water has been drained, follow the “COLLECT” procedure above. www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •...
-
Page 9: Maintenance Instructions
1. Loosen the four screws on the front of the M5400H Alarm Panel Box and carefully remove the cover. 2. Take note of the current thermostat set-point. Thermostat Set-Point: __________________ www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •... -
Page 10: Changing Timer Setting
The default setting of 60º F is adequate for outside temperatures down to 0º F. If operating below this temperature, the set- point should be increased. Consult AGF for set-point guidelines. 1. Disconnect electrical power to the M5400. -
Page 11: Maintenance Log
_________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ _________ ________________________________________________ ________ www.agfmfg.com AGF Manufacturing • Phone: 610-240-4900 • Fax: 610-240-4906 •... -
Page 12: Agf Manufacturing
AGF Manufacturing 100 Quaker Lane • Malvern, PA 19355 Phone: 610-240-4900 Fax: 610-240-4906 www.agfmfg.com...
Need help?
Do you have a question about the COLLECTANDRAIN 5400B and is the answer not in the manual?
Questions and answers