Trampoline Assembly - BorMann BSP1086 Manual

E N

9. TRAMPOLINE ASSEMBLY

Please refer to TRAMPOLINE PARTS LIST for identification of
parts (chapter 8).
Two adults in good physical condition are required for the following assembly.
For your safety, you should wear proper shoes and clothing. Failure to follow
these instructions and warnings may result in injury.
NOTE:
Picture may vary slightly with different trampoline models.
TRAMPOLINE ASSEMBLY PROCEDURE
(follow the figures in page 3)
1.Lay out all the trampoline parts in groups, shown above.
2.Attach the leg extensions to a leg base and secure together with the screws.
Repeat for all leg supports.
3.Attach all the top rails to form a large circle. Joining the last link may require
two people. The second person should hold the opposite side, while you
bring to both ends of the circle together.
4.Attach the all leg supports you assembled in STEP 2 to the top frame.
5.Attach the leg support to the top frame and tightly secure together with the
screws.
6.At this stage the trampoline should be like the picture in Fig. 6.
7.With stitching portion facing down lay jumping mat inside frame and attach
a spring into one of the triangle rings on the mat. Then attached the other end
of the spring to the frame.
8.Repeat STEP 7 directly across from where you attach the first spring. Then
attach two more springs half distance between the first two springs, directly
across from each other. This will ensure equal tension is distributed between
the springs.
9.Repeat process for the remaining springs. Use the spring tool, as shown
above. Warning: During spring assembly, please be careful where you place
your hands other parts of your body as connector points.
10.Springs under heavy tension may require adjacent springs to be attached at
every four or five holes. So the spring tension is distributed equally.
11.Attach the remaining springs until all springs are attached onto the frame.
12.Lay the cover pads on the outer edge so the springs are covered.
13.Attach all the cover pad's strings onto the springs.
14.Proceed to Testing the Trampoline section of this manual before jumping on
the trampoline.
9
WARNING:
WWW.NIKOLAOUTOOLS.GR
10. SAFETY ENCLOSURE PARTS LIST
ITEM
A
B
C
D
E
F
A. Upper pole
C. Safety Net
E. Assemble tool
11. SAFETY ENCLOSURE ASSEMBLY
I. Insert the lower pole into the upper pole, repeat for all poles.
II. Place the safety enclosure mesh on trampoline tidily, as shown above,
ready for the next step.
III. Slide the enclosure poles you assembled into the safety enclosure mesh
poles jacket (Fig.II, page 4)
IV. Repeat STEP 3 for all the enclosure poles, make sure you insert the poles
firmly into the jacket.
V. You may need another person to hold the enclosure pole in place while
you clamp the pole to leg supports in the next step.
VI.Use the quick clamp to secure the enclosure pole to the hole of the leg
extension and the hole of T bar.
VII. Repeat STEP 5 to STEP 6 for the remaining poles.
VIII. Safety enclosure hooks when released should look like the figure VIII,
page 4.
IX. Attach the hooks to the nearest triangle ring of the mat, if you find it diffi-
cult to attach the hooks to the triangle rings follow the instructions of Fig X.
X. Attach the hooks to the ring portion of the spring.
XI. Zip the entrance close, and fasten all the entrance hooks. Supervisors
must re-zip and re-hook all the entrance hooks securely before jumping be-
gins.
XII. Your trampoline now looks like the one in Fig. XII.Proceed to testing the
trampoline section of this manual before jumping on the trampoline. For
disassembly, please follow the assebly instructions in reverse order.
Model 8FT (Number)
Upper Pole 6
Lower Pole 6
Safety Net 1
Quick Clamp 12
Asseble Tool 1
Ladder 1
B. Lower Pole
D. Quick clamp
F. Ladder