Advertisement
<M2> LOWER ASS'Y(F)
BKT(OP)
555
E
A
558
A
CONNECT
556
E-CARD WIRE
F
[K185: Non Megapixel CCD MODEL]
(WR551a)
CONCLUSION SCREW TORQUE TABLE
PART.NO
TORQUE
0.09 ±0.009 N•m
ALL SCREW
<M2> LOWER ASS'Y(G)
CONCLUSION SCREW TORQUE TABLE
PART.NO
ANOTHER SCREW
513
BATT.TERMINAL
507
FPC
508
A
SOLDERING
ARM ASS'Y
504
521
514
522
D
BE CAREFUL NOT TO TOUCH BY THE FINGER, AND BE CAREFUL
NOT TO BEND THE TERMINAL FPC OF CAMERA OPE UNIT.
(USE TWEEZERS OR FINGER STALL)
(COUNTERMEASURE OF MIGRATION)
1-4
[J7C: Megapixel CCD MODEL]
BKT(OPJ7C)
555
558
OP F. ASS'Y
[J7C]
G
G
(Refer to the
Exploded view
for this part.)
(SD551a)
(WR551a)
OP F. ASS'Y
[K185]
(Refer to the
F
Exploded view
for this part.)
<03>
BENT 180" TO SIDE OF
SD BOARD ASS'Y
REIN FOR CEMENT BOARD
OF CCD PWB ASS'Y
557
(SD551a)
559
(WR553a)
F
(WR552a)
B
559
D
TORQUE
0.07 ±0.009 N•m
514
0.12 ±0.01 N•m
HOLDER
(G.OUTER)
515
B
513
BKT(S.COVER/VF)
510
E
D
A
B
515
C
Fig. 1-2-2b LOWER ASS'Y(F), LOWER ASSY(G)
[For Non Megapixel CCD MODEL]
MIC ASS'Y
562
LOWER ASS'Y(G)
(Refer to the Exploded
view for this part.)
B
D
552
560
E
C
BE CAREFUL NOT TO TOUCH BY THE FINGER, AND BE CAREFUL
NOT TO BEND THE TERMINAL FPC OF CAMERA OPE UNIT.
(USE TWEEZERS OR FINGER STALL)
(COUNTERMEASURE OF MIGRATION)
553
VF ASS'Y(G)
(Refer to the Exploded
view for this part.)
LOWER ASS'Y(F) LYH20622
502
KNOB(DSC)
503
SIDE COVER ASS'Y
<04>
SIDE OPE
BOARD ASS'Y
E
519
E-CARD WIRE
509
(WR553a)
515
505
CASS.COVER ASS'Y
C
506
CAMERA OPE UNIT
512
PROCESSING E-CARD WIRE (ONLY THE MODEL OF OP ASS' Y OF K185).
DRAWING FOR SPACER STICKING.
[K185: Non Megapixel CCD MODEL]
AFTER ASSEMBLY
BENT 180" PART
OF E-CARD WIRE.
570
PASTE
SPACER
PROCESSING J7C OP ASS'Y.
561
[J7C: Megapixel CCD MODEL]
PASTE SPACER
TO COVER FPC OF OP ASS'Y.
BENT
PASTE ALONG THIS LINE.
PASTE
567
PASTE SHIELD INSIDE FPC.
SHEET(SHIELD)
PROCESSING K185 OP ASS'Y AND MIC WIRE.
PASTE SPACER TO COVER
[K185: Non Megapixel CCD MODEL]
FPC OF OP ASS'Y.
INSID BRACKET PART
OF OP ASS'Y.
SPACER(A)
SPACER(A)
563
565
PASTE TO CORNER OF OP ASS'Y.
SPACER(A)
PASTE TO
564
565
SPACER(A)
ACCORD.
PASTE SO THAT SIDE OF
BKT(OP) MAYBE HIDDEN.
566
SPACER IS TWISTED AND
SPACER(A)
WIRE CAN'T BE SEEN.
LESS THAN 1 mm.
LOWER ASS'Y(G) LYH20620
PROCESSING GRIP BELT.
GRIP BELT
PROCESSING BATT. FPC
SHEET(BAT.FPC)
SHOULD BE COVERED
DON'T STICK OUT
516
TERMINAL PART.
BATT. FPC IN
SHOULD NOT BE
ARM BRACKET.
COVERED SCREW HOLE.
520
SPACER(A)
DRAWING FOR SPACER STICKING.
PASTE SPACER AFTER ATTACHING BATT. TERMINAL.
STICK ALONG
SPACER(A)
SPACER(A)
THE EDGE OF ARM.
518
518
STICK ALONG
STICK ALONG
THE EDGE
THE EDGE
OF ARM.
OF ARM.
SPACER IS NOT
PROTRUDED FROM
ARM BRACKET.
SPACER(A)
SHIELD(CCD)
568
PASTE
BENT
561
SPACER(A)
DON'T PASS MIC WIRE ON THIS SCREW.
PASS MIC WIRE INSIDE BKT(OP).
DRAWING FOR AFTER ASSEMBLY BKT(OP).
ATTACHING
511
PROCESSING CAP(GRIP BELT).
CAP(GRIP BELT)
523
ATTACH
CAP(GRIP BELT)
THAT WIDTH IS WIDER
BECOME REAR SIDE.
PROCESSING STICKER.
LABEL(C.COVER)
517
1 ±1 mm
Advertisement
