MULTIQUIP GloBug GB113BC Operation And Parts Manual page 36

23
DANGER
Make sure that generator is loaded when
conveying Lighting Tower by forklift.
Be sure to insert forks at marked position
exactly under pipe frame or base plate
CART
DANGER
Make sure that generator is loaded when
23
conveying Lighting Tower by forklift.
Be sure to insert forks at marked position
exactly under pipe frame or base plate
1
CAUTION
COVER
INFORMATION
Before operating GloBug
ALWAYS unzip cover, fold into
bag on top of balloon and zip.
Bag Zipper
Cover
NEVER apply power to the
GloBug until the cover has
been inserted inside the bag
and the balloon is fully exposed.
B e f o r e s t o r i n g G l o B u g ,
ALWAYS fully cover balloon to
prevent damage from dust, dirt
and adverse weather conditions.
DCL413
DANGER
ELECTRICAL
SHOCK HAZARD
NEVER touch a live power cord
or active electrical components
21 with wet hands or while standing
in water. The possibility of electrical
shock or even death! exists.
DCL410
20
WARNING
BURN HAZARD
To prevent burns, NEVER
touch ballast or cover while
lamp is on. These surfaces are
extremely hot! ALWAYS allow
sufficient time for both surfaces
to cool down before touching.
DCL415
BALLAST
BOX
PAGE 36 — GB113BC GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #5 (01/16/12)
A400116400
A400116400
CAUTION
When the GloBug is used for
6
non-lighting applications, ALWAYS
un-plug GloBug AC power cord
from the generator.
7
8
22
ON
DANGER
ELECTRICAL
SHOCK HAZARD
NEVER place the GloBug
OFF
wheels in standing water. The
possibility of electrical shock,
even death! Exists. DCL408
DCL400
10
MODEL
19
SERIAL NO.
18
HIGH VOLTAGE
NAMEPLATE AND DECALS
2
CAUTION
LAMP COVER BUZZER
Before operating GloBug
ALWAYS unzip cover, fold into
bag on top of balloon and zip.
I f the cover has not been removed
a n audible alarm will sound when
power is applied to the GloBug.
WARNING
When lifting of the GloBug is
required, ALWAYS attach a rope
or chain to the lift hanger. DO NOT
use any other lifting points to
lift the GloBug.
LIFT
HANGER
3
DANGER
ELECTRICAL
SHOCK HAZARD
When replacing lamp and to prevent electrical
shock, ALWAYS shutdown the generator before
replacing lamp. Remember to let lamp cool before
removing. Use only recommended type lamp as
listed in parts manual.
LAMP INFORMATION
ALWAYS
first, before shutting down
generator.
Once lamp is turned
Allow lamp to cool down
before turning back on.
I t will take about 20 minutes
before lamp can be turned
DCL402
back on.
0 0
6 0
DCL401
- 6 H
G A
WARNING
To avoid injury,
you MUST read
and understand
operator's manual
before using this
machine.
CAUTION
This machine to
be operated by
TIRE PRESSURE
qualified
personnel only. ALWAYS keep tires inflated
to correct pressure. Low or
Ask for training
incorrect tire pressure could
as needed.
result in brake malfunction.
P/N 35137
Recommended tire pressure:
35.5 PSI
(225 kPa)
9
17
DANGER
DCL418
DCL404
DCL412
DCL412
WARNING
BURN HAZARD
To prevent burns,
touch lamp while lamp is on.
Lamp surface gets extremely
DCL416
hot! ALWAYS
time for lamp to
before touching.
4
WARNING
ADJUSTMENT
CAUTION
LEVER HAZARD
BE CAREFUL NOT TO
STRIKE HEAD AGAINST
TOWER ADJUSTMENT
11
turn lamp OFF
LEVER. POSSIBLE HEAD
INJURY CAN OCCUR.
OFF,
DCL409
DCL406
ELECTRICAL
SHOCK HAZARD
ALWAYS MAKE SURE AREA ABOVE
TOWER MAST IS OPEN AND
OF OVERHEAD
THE TOWER MAST EXTENDS IN
EXCESS OF 16.5 FT. (5 METERS).
0N ON
OF F
F
E OF
IDL OL TION
CO NTR SWIT OPE RA CH
0V A
12 20
0V
0V /24 ER
12 L POW H
O FF FUL SW ITC
20 A
A 0V
21 12 A
CU IT 30
CIR KE R
AC BR EA
0/ 24 0V A
12 30
DANGER
GloBug
INFORMATION
To prevent tipping, NEVER
in winds that exceed 22 mph
(10 m/sec).
NEVER use on an incline of 5
degrees or more. The possibility
of tipping exists.
NEVER use in rain or wet
conditions. The possibility of
electrocution exists.
ALWAYS apply parking brake
to prevent moving.
When moving is required, lower
mast fully.
W hen raising mast, ALWAYS
deploy outriggers to prevent
tipping.
DANGER
ALWAYS turn OFF generator
before performing maintenance.
ELECTRICAL
SHOCK HAZARD
15
GROUND
To prevent electrical shock or
electrocution, the generator
MUST be connected to an
earth ground.
(See NEC Article 250)
DCL405
WARNING
OUTRIGGER
DCL407
DEPLOYMENT
SETTING:
Pull outrigger upward at the tip end
and rotate backwards until it locks in
place.
STOW
POSITION
ON
0N IDLE OFF CONTROL OPERATION SWITCH OFF
120 V 120V 20A
21A OFF 21A OFF 120V 120V/240V SWITCH 20A FULL POWER
0 BREAKER 120/240V 30A 30A CIRCUIT 120/240V AC AC CIRCUIT BREAKER 30A
600
GA-6 H
16
RELEASE:
To unlock outrigger, push downward
on the counter-weight lever indicated
by arrow. Grab hold of outrigger, pull
upward, push down and place in stow
position.
DCL414
NEVER
allow sufficient
cool down
DCL417
5
12
DANGER
CLEAR
POWER LINES .
13
OFF ON OFF 0N
OFF 120V SWITCH FULL CONTROL IDLE 120V/240V SWITCH POWER OPERA TION 20A
AC CIRCUIT BREAKER 21A 20A 30A 120V
6000 30A 120/240V
GA-6H
DCL403
use
14
DCL411