Operation; Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL 40.206.50 Original Operating Instructions

7. Operation

7.1 Tire pressure gauge with adapters (Fig. 3)
Working pressure in bar: 0 – 8
Range of applications:
The tire pressure gauge (14) allows you to infl ate
car tires easily and exactly. Use the pressure
gauge to check the tire pressure. If the tire pres-
sure is too high, you can reduce the pressure with
the integrated relief valve (e). The tire pressure
gauge comes with a valve adapter for car tire
valves.
Warning! Observe the information supplied by
the tire manufacturer and the vehicle manufactu-
rer relating to the recommended tire pressure.
Warning! This equipment is not calibrated! For a
calibrated measurement value, check the actual
tire pressure using a calibrated meter after you
have infl ated the tires yourself, e.g. at a petrol
station.
Use as a blow-out pistol
To use the tire pressure gauge as a blow-out
pistol you must fi rst unscrew and remove the
hose with the valve adapter for care tires. Now the
blow-out adapter (15) can be screwed to the tire
pressure gauge.
Range of applications:
For cleaning and blowing out hollow spaces or
hard-to-reach areas, as well as for cleaning soiled
equipment. The infi nitely variable trigger lever al-
lows an exact dosing of compressed air.
7.2 Instructions for the adapter set
For information on the correct use of the adapters
for the various valves, please refer to the following
overview (see Fig. 11 which shows how to con-
nect the adapter to the compressor).
•
Ball needle (Fig. 4)
Area of application: For inflating balls. The
ball needle can be used to inflate a variety of
different balls.
TIP: To avoid damaging the valve, moisten
the needle slightly before inserting it.
•
Valve adapter (Fig. 5)
Area of application: For Dunlop cycle tire
valves.
This Dunlop valve adapter is designed for
inflating cycle tires.
Anl_TC_AC_190_6_8_OF_Set_SPK9.indb 18 Anl_TC_AC_190_6_8_OF_Set_SPK9.indb 18
GB
•
Adapter I (Fig. 6/Item I)
Area of application: For all valves with an in-
ternal diameter of 8 mm or more.
You can use this adapter to inflate airbeds,
pools and even boats.
TIP: Insert the adapter I into the valve as
shown in Figure 6, drawing d.
Important! The valve cap must be opened a
little by being pressed together slightly.
•
Adapter II (Fig. 7/Item II)
Area of application: For screw valves. This ad-
apter can be used for all conventional boats,
kayaks and other large items such as pools,
which are fitted with a screw valve.
•
Vent adapter (Fig. 8/Item III)
Area of application: For deflation valves you
can find a deflation valve combined with other
valves (standard valve, screw valve, etc.)
on many large articles such as an inflatable
mattress.
•
Conical universal adapter (Fig. 9-10)
Area of application: The universal adapter can
be used for inflating airbeds and other similar
items.

8. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
9. Cleaning, maintenance and
ordering of spare parts
Danger!
Pull the power plug before doing any
cleaning and maintenance work on the ap-
pliance.
Warning!
Wait until the compressor has completely
cooled down. Risk of burns!
Warning!
Always depressurize the tank before carrying
out any cleaning and maintenance work.
Danger!
After use, always switch off the equipment
immediately and pull out the power plug.
- 18 -
10.07.2019 10:08:20 10.07.2019 10:08:20