6 digit programmable counter / timer relay, with prescaling and eeprom data storage (40 pages)
Summary of Contents for Trumeter 898X
Page 1
Model 898X Electronic Preset Counter with two presets Model 899X Contador electrónico de preselección con dos preselecciones Elektronischer Vorwahlzähler mit zwei Vorwahlen Compteur à présélection électronique avec deux présélections Contatore elettronico a preselezione con due preselezioni 022792-01 Issue 1.1 04/18...
Table of Contents (German is the original version) Preface Safety instructions and Warnings Use according to the intended purpose Mounting in a control panel Electrical Installation Cleaning and maintenance Description Display/Operating elements Inputs INP A, INP B RESET GATE LOC.INP MPI 1 / MPI 2 Outputs Output 1 / Output 2...
Page 3
11.4 Timer 11.5 Signal and Control Inputs 11.6 Outputs 11.7 Supply Voltage 11.8 Sensor Supply Voltage 11.9 Climatic Conditions 11.10 EMC 11.11 Device Safety 11.12 Mechanical Data 11.13 Connections 12 Scope of Delivery 13 Ordering Codes 14 Frequencies (typical) 14.1 Pulse Counter 14.2 Frequency Meter 15 Input modes: Pulse counting 16 Input modes: Timing...
The application area for this device lies in industrial Preface processes and controls, in the fields of manufacturing lines for the metal, wood, plastics, Please read this instruction manual paper, glass, textile and other like industries. Over- entirely and carefully before installation voltages at the terminals of the device must be kept and start-up.
unused screw terminals must be screwed to the Electrical Installation stop, so that they cannot loosen and get lost. The device must be disconnected • The device has been designed for overvoltage from any power supply prior to any category II. If higher transient voltages cannot be installation or maintenance work.
Multiplication and division factor RESET Averaging and Start Delay for frequency meter Dynamic reset input: resets the pulse counter or Input modes: timer to zero (‘Add’ output operations) or to preset Pulse counter: cnt.dir, up.dn, up.up, quad, quad2, value 2 (‘Sub’ output operations). The reset input quad4, A/B, (A-B)/Ax100% can be inhibited in the programming menu.
The security prompt YES Change the count value using appears in the display the UP key or the DOWN key. Enter the main menu by pressing Press the ENTER key. the ENTER key The new setting is again displayed flashing. The first menu item in the main menu appears in the display Ending the programming...
Select language for Help Text Totalising [A + B] INP A: count input add English INP B: count input add German (Deutsch) Quadrature input INP A: count input 0° When ‘Help Text ON’ is selected, a INP B: count input 90° running text in English or German Quadrature with pulse automatically appears after 3 sec.
Page 9
When the Lock input is activated, Electrical reset sets only the the setting of the preset values main counter to zero. and the programming are both Count mode SUBTRACTING inhibited. with automatic reset and Batch counter 7.8.3.2 Submenu for Output operations Output 2 (timed signal) active when main counter = zero Submenu for determining the...
When preset 2 is changed then Electrical Reset: preset 1 automatically tracks it. Always resets only the main counter. Reset to zero. Automatic reset to zero when Manual Reset: main counter = preset value 2. Resets the main counter (ACTUAL) and Preset 1 relative to Preset 2 auxiliary counters (BATCH or TOTAL), if the value of the main counter or the value of an...
INP A: Frequency input A Decimal point setting INP B: Frequency input B (determines the resolution) no decimal place Percentage differential 1 decimal place measurement [(A-B) / A in %] 0.00 2 decimal places INP A: Frequency input A 0.000 3 decimal places INP B: Frequency input B Moving average...
Page 12
Input mode Time measurement 7.8.5.2 Submenu for output operations (see also under 16.) Submenu for determining the operation of the outputs Start: Edge to INP A Stop: Edge to INP B Output operation (See also under 18.) Start: 1. Edge to INP B Stop: 2.
Page 13
main counter = zero main counter = preset value 2. Batch counter counts the number Preset 1 relative to Preset 2 of automatic repetitions of preset 7.8.5.3 Submenu for configuration Output 1 active when batch Submenu for matching the input counter >...
Page 14
with positive direction and when 7.8.5.5 Submenu for Preset 1 count > Preset 1 Submenu Preset 1 ADD mode output operations: timed signal at Output1, Preset 1 ON/OFF becomes passive with positive Preset 1 ON direction and when count > Preset 1 and subsequently Preset 1 OFF and no function passive with negative direction...
becomes passive when count < Operation zero (Deactivation only in negative direction). Switching the display during ADD mode output operations: operation timed signal at Output 2, Pressing the DOWN key or the becomes active with positive UP key once causes the name of direction and when count >...
8.2.2 Teach Function Default Parameters Note: Three default parameter sets have 1. In the programming menu, programme MPI been permanently stored; these can be input 1 or MPI input 2 (MP.INP.1 / MP.INP.2) adapted as required. With each to TEACH acknowledgment of the parameter sets, all 2.
8.4.4 Parameter Set Table 10.1 Signal and Control Inputs P.SET1 P.SET2 P.SET3 N° Designation Function HLP.TXT. INP A Signal input A SL.LANG. INP B Signal input B FUNCT COUNT COUNT COUNT RESET Reset input INP.POL. LOCK Keypad lock FILTER GATE Gate input CNT.DIR UP.DN...
11.3 Tacho/Frequency Meter 11.7 Supply Voltage Frequency range 0.01 Hz to 65 kHz (see AC supply: 100 ... 240 V AC / max. 11 VA under 14. Frequencies typ. 50/60 Hz, Tolerance ± 10% ext. fuse protection: T 0.1 A Measuring principle ≤...
15 Input modes: Pulse counting PNP: Count on rising edge Function Diagram NPN: Count on falling edge Note: No counting when GATE input is active P = Preset CNT.DIR Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset ->...
Page 21
Function Diagram PNP: Count on rising edge NPN: Count on falling edge Note: No counting when GATE input is active QUAD4 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Count input Count on rising and on falling edges, Reverse direction Add: Display 0 -->...
17 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge Inp A: Frequency input Inp B: no function A - B Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B A + B Inp A: Frequency input 1 Inp B: Frequency input 2...
19 Help Texts PROG. NO PROGRAMMING PROG. START PROGRAMMING LANGU. MAIN MENU SELECT LANGUAGE HLP.TXT. HELPTEXT ON SL.LANG. DEUTSCH SL.LANG. ENGLISH FUNCT. MAIN MENU BASIC FUNCTION FUNCT. COUNT BASIC FUNCTION COUNTER FUNCT. TIMER BASIC FUNCTION TIMER FUNCT. TACHO BASIC FUNCTION TACHOMETER/FREQUENCY METER INPUT MAIN MENU INPUTS INP.POL.
Page 27
MODE SUB.AR MODE SUBTRACTING WITH AUTOMATIC RESET MODE SUB.BAT MODE SUBTRACTING WITH AUTOMATIC RESET + BATCH COUNTER MODE SUB.TOT MODE SUBTRACTING WITH AUTOMATC RESET + TOTAL COUNTER CONFIG. MAIN MENU CONFIGURATION FACTOR MULTIPLICATION FACTOR DIVISO. DIVISION FACTOR T.MODE TIME RANGE SECONDS T.MODE TIME RANGE MINUTES T.MODE...
20 Dimensional Drawings Dimensions in mm [inch] Rear view: Panel cut-out: [3.622 +0.8 +0.031 Terminal Assignment: Signal and control inputs Version with relay/optocoupler Output 2 Output 1 RS232 RS485 (optional) (optional) – Power supply connected through – – – – Page 28 | ENG...
Need help?
Do you have a question about the 898X and is the answer not in the manual?
Questions and answers