Advertisement
M1500
CORDLESS HEADSET SOLUTION WITH BLUETOOTH
1
W E L C O M E
Welcome to the cutting edge of hands-free and
wire-free technology for mobile phones. Here
are the components to your Plantronics M1500
headset and adapter solution.
TALK/POWER BUTTON/INDICATOR LIGHT
NOISE-CANCELLING
BOOM
DEVICE
MUTE/VOLUME
M1500 HEADSET
CONTROL
POWER
JACK
EARLOOP POST/
HEIGHT ADJUSTMENT
SPEAKER
MICROPHONE
EARLOOP
(FLEXIBLE FOR FIT)
5
U S I N G Y O U R H E A D S E T
FIG. 5.1 – TURNING THE HEADSET
ON AND OFF
FIG. 5.1
• To turn your headset on, press
and HOLD the blue TALK button until
the button lights.
The INDICATOR will light continuously
for a few seconds and then turn off.
3 SECONDS
• To turn your headset off, press
and HOLD the TALK button for about
3 SECONDS
3 seconds or until you hear a tone.
FIG. 5.2
The INDICATOR will flash twice and
the headset will turn off.
• To check if your headset is turned on
or off, hold the unit to your ear and
ROTATE the MUTE/VOLUME dial.
If you hear a tone, your headset is
turned on.
FIG. 5.2 – TURNING THE ADAPTER
FIG. 5.3A
ON AND OFF
• To turn your adapter on, press
and HOLD the blue POWER button
until the INDICATOR lights and
then release.
The INDICATOR will flash green
while the unit is on.
• To turn your adapter off, press
FIG. 5.3B
and HOLD the POWER button for
about 3 seconds, or until the
indicator turns red and then release.
The INDICATOR will flash twice and
the adapter will turn off.
2
G E T T I N G S TA R T E D
Install, activate and charge the batteries.
– Open the battery compartment
FIG. 2.1
FIG. 2.1
by pulling on the two battery door latches.
Remove the door.
– Insert battery into compartment
FIG. 2.2
so the (+) and (-) symbols correspond
correctly. Replace battery compartment
door by inserting the small tabs nearest
the speaker and then snapping the door
into place.
TRANSFER/POWER BUTTON
HANDSET
CONNECTION
BATTERY DOOR
A500 ADAPTER UNIT
ACCEPTING A CALL
FIG. 5.3 – HANDLING CALLS
• As soon as your handset rings, press
• Make sure both your headset and
the TALK button on your headset
adapter are turned on and the
to establish a connection between the
adapter is connected to your phone.
headset and adapter. You will hear
MAKING A CALL
a tone and the INDICATOR lights on
• Press the TALK button on your headset
both the adapter and headset will
to establish a connection between the
begin to flash red.
headset and adapter. You will hear a
• Answer the call using your handset
tone and the INDICATOR lights on
SEND key.
both the adapter and headset will
• When your call is complete, press
begin to flash red.
the TALK button on your headset
• Dial using your mobile phone keypad
to disconnect the adapter. The
and press the SEND key to place a
INDICATOR light on the adapter will
call. You will hear the call progress in
return to flashing green.
your headset.
• When your call is complete, press the
FIG. 5.4 – ADJUSTING THE VOLUME
• To increase volume, ROTATE the
TALK button on your headset to dis-
MUTE/VOLUME dial up and release
connect the adapter. The INDICATOR
(for headset usage on right ear).
light on the adapter will return to
• To lower volume, ROTATE the MUTE/
flashing green.
VOLUME dial down and release (for
NOTE
— To prevent shortened battery
headset usage on right ear).
life, make sure the adapter INDICA-
• Also adjust the volume on your
TOR light is flashing green between
handset.
calls. If the adapter INDICATOR
— If using the headset on your
NOTE
light is flashing red and you are not
left ear, reverse the instructions,
using your headset, press the TALK
rotating down to raise volume, and
button on the headset to disconnect
up to lower it.
the adapter.
™
FIG. 2.2
FIG. 2.3
CORD
INDICATOR
LIGHT
FIG. 2.4
POWER JACK
FIG. 5.5 – MUTE FUNCTION
• To mute the microphone while on a
call, PUSH IN on the MUTE/VOLUME
dial. A tone, followed 2 seconds
later by a reminder tone, indicates
mute function.
• To disable the mute, PUSH IN on the
MUTE/VOLUME dial again. A beep
indicates Mute function is off.
FIG. 5.4
ROTATE
FIG. 5.5
PUSH IN
3
CONNECTING TO YOUR HANDSET
FIG. 2.3
– Locate the white vinyl strip
protruding from the rear of the adapter
FIG. 3.1A
unit. Remove the strip by pulling it directly
out of the slot to activate the battery.
– Connect the included wall
FIG. 2.4
charger to AC power and then to both
the headset and adapter power jacks.
In a few seconds, the INDICATOR lights
will begin to blink. The INDICATOR lights
will stop blinking and turn off when the
headset and adapter are fully charged.
The first charge takes 2 hours; subsequent
charges take just 1 hour. A fully charged
headset and adapter will provide
approximately 3 hours of talk time and
3 days of standby. Recharging your
batteries each night will ensure your
FIG. 3.1B
headset is ready for use the next day.
The batteries used in this product must be
recycled or disposed of properly. Contact
your local recycling center for proper
disposal instructions.
4
G E T T I N G T H E P E R F E C T F I T
Customize your headset so that it fits
comfortably.
FIG. 4.1
– Rotate the earloop outward.
FIG. 4.1
FIG 4.2
– Position the headset over
your right ear so that the earloop slides
behind your ear. Bend the flexible ear-
loop to achieve a snug, comfortable fit.
FIG. 4.2
– Adjust the microphone BOOM
FIG 4.3
so it is aligns with your mouth.
– For left ear usage, simply
FIG 4.4
remove the earloop from the headset, flip
the headset over and reinsert the earloop
on the opposite side. After completing
this step, follow the fit instructions above
— except using your left ear.
– If the speaker sounds soft or feels
FIG. 4.3
NOTE
uncomfortable, slide the headset up or
down along the earloop post so that it is
centered on your ear when fitted.
FIG. 4.4
You may attach the adapter unit directly
to your handset or carry it separately
in the supplied belt pouch. Before attach-
ing the unit to your handset, place a
few calls (see Section 5) and determine
a position that provides the best audio
performance.
FIG. 3.1 – ATTACHING DIRECTLY TO
HANDSET
• Select a location on your handset
to attach the adapter unit. Make
sure the attachment point is flat and
large enough to fit the supplied
tape/Velcro patches.
• NOTE
– Choose a location that does
not require you to completely cover
the adapter with your hand when
using your headset. Consider using
the provided belt pouch for the best
audio performance.
• Check that the adapter unit cord
will connect to the headset-jack on
your handset without interfering with
normal usage.
– Make sure that when the
• NOTE
adapter unit is fixed to your handset,
other accessories you use (belt clips,
car kits or charging stations) can
connect and work properly.
• Peel the backing off one side of the
tape/Velcro patch and attach it square-
ly to the back of the adapter unit.
• Peel off the other (exposed) side of
the tape/Velcro patch and secure it to
your handset.
• Now attach the adapter unit to
your handset and connect the cord
to the headset-jack. See your mobile
phone user guide for instructions for
connecting a headset.
FIG. 3.2 – USING THE BELT POUCH
• Open the pouch and slide in the adapter
unit with the power jack facing down.
• With the pouch open, slip the adapter
cord through the rectangular slot
in the top flap and close the pouch.
• Slide the pouch onto your belt
and attach the adapter cord to
your handset.
• When using the belt pouch,
remember to unplug the adapter
before you answer or make a call
using your handset.
FIG. 3.2
Advertisement
