Table of Contents
Advertisement
Quick Links
P.O. BOX 265
OGDENSBURG, NY
U.S.A. 13669-0265
A V T E C H
TEL: 888-670-8729 (USA & Canada) or +1-613-686-6675 (Intl)
FAX: 800-561-1970 (USA & Canada) or +1-613-686-6679 (Intl)
info@avtechpulse.com
INSTRUCTIONS
MODEL AV-110C-PS-D
0 to ±100V, 200 kHz
VARIABLE-GAIN DUAL-CHANNEL
LINEAR AMPLIFIER
SERIAL NUMBER: ____________
E L E C T R O S Y S T E M S
N A N O S E C O N D
W A V E F O R M
S I N C E
-
http://www.avtechpulse.com/
E L E C T R O N I C S
1 9 7 5
BOX 5120, LCD MERIVALE
X
OTTAWA, ONTARIO
CANADA
1
L T D .
K2C 3H4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Avtech AV-110C-PS-D
Summary of Contents for Avtech AV-110C-PS-D
- Page 1 TEL: 888-670-8729 (USA & Canada) or +1-613-686-6675 (Intl) BOX 5120, LCD MERIVALE OGDENSBURG, NY FAX: 800-561-1970 (USA & Canada) or +1-613-686-6679 (Intl) OTTAWA, ONTARIO U.S.A. 13669-0265 CANADA K2C 3H4 info@avtechpulse.com http://www.avtechpulse.com/ INSTRUCTIONS MODEL AV-110C-PS-D 0 to ±100V, 200 kHz VARIABLE-GAIN DUAL-CHANNEL LINEAR AMPLIFIER SERIAL NUMBER: ____________...
-
Page 2: Warranty
Avtech product is found to be defective, Avtech shall at its option repair or replace said defective item. This warranty does not apply to units which have been dissembled, modified or subjected to conditions exceeding the applicable specifications or ratings. -
Page 3: Table Of Contents
TABLE OF CONTENTS WARRANTY........................2 TECHNICAL SUPPORT....................2 TABLE OF CONTENTS....................3 INTRODUCTION.......................5 HIGH-VOLTAGE PRECAUTIONS..................5 SPECIFICATIONS......................6 REGULATORY NOTES....................7 FCC PART 18.......................... 7 EC DECLARATION OF CONFORMITY..................7 DIRECTIVE 2002/95/EC (RoHS).....................8 DIRECTIVE 2002/96/EC (WEEE)....................8 AC POWER SUPPLY REGULATORY NOTES...............9 INSTALLATION......................10 VISUAL CHECK........................10 POWER RATINGS........................10 CONNECTION TO THE POWER SUPPLY................10 PROTECTION FROM ELECTRIC SHOCK................11 ENVIRONMENTAL CONDITIONS..................12... - Page 4 PCB 158N - LOW VOLTAGE POWER SUPPLY, 2/3............25 PCB 158N - LOW VOLTAGE POWER SUPPLY, 3/3............26 PCB 168B - HIGH VOLTAGE DC POWER SUPPLY............27 MAIN WIRING........................28 PERFORMANCE CHECK SHEET..................29 Manual Reference: /fileserver2/officefiles/instructword/av-110/AV-110C-PS-D,ed3.odt. Last modified August 8, 2012. Copyright © 2012 Avtech Electrosystems Ltd, All Rights Reserved.
-
Page 5: Introduction
INTRODUCTION The AV-110C-PS-D is a variable-gain dual-channel linear amplifier. The gain for each of the two independent channels may be adjusted from +1 to +50. The input range is 0 to ±2V, and the output range is 0 to ±100V. The outputs can drive load impedances of 10 kΩ... -
Page 6: Specifications
SPECIFICATIONS Model: AV-110C-PS-D Output Amp. (max): ± 100 Volts Load impedance: ≥ 10 kΩ Bandwidth: DC to 200 kHz Voltage gain (variable): ×1 to ×100 Input range: 0 to ± 2 Volts (1 kΩ input impedance) Rise time (20%-80%, for max 0.6 us... -
Page 7: Regulatory Notes
If interference is observed, check that appropriate well-shielded cabling is used on the output connectors. Contact Avtech (info@avtechpulse.com) for advice if you are unsure of the most appropriate cabling. Also, check that your load is adequately shielded. It may be necessary to enclose the load in a metal enclosure. -
Page 8: Directive 2002/95/Ec (Rohs)
Directive 2002/96/EC categories 1-7 and 10, as stated in the "Article 2 - Scope" section of Directive 2002/95/EC. DIRECTIVE 2002/96/EC (WEEE) European customers who have purchased this equipment directly from Avtech will have completed a “WEEE Responsibility Agreement” form, accepting responsibility for WEEE compliance (as mandated in Directive 2002/96/EC of the European Union and local laws) on behalf of the customer, as provided for under Article 9 of Directive 2002/96/EC. -
Page 9: Ac Power Supply Regulatory Notes
AC POWER SUPPLY REGULATORY NOTES This instrument converts the AC input power to the +24V DC voltage that powers the internal circuitry of this instrument using a Tamura AAD130SD-60-A switching power supply. According to the manufacturer, the Tamura AAD130SD-60-A has the following certifications: UL60950-1 IEC60950 -1... -
Page 10: Installation
INSTALLATION VISUAL CHECK After unpacking the instrument, examine to ensure that it has not been damaged in shipment. Visually inspect all connectors, knobs, and handles. Confirm that a power cord is with the instrument. If the instrument has been damaged, file a claim immediately with the company that transported the instrument. -
Page 11: Protection From Electric Shock
5. Do not attempt any repairs on the instrument, beyond the fuse replacement procedures described in this manual. Contact Avtech technical support (see page 2 for contact information) if the instrument requires servicing. Service is to... -
Page 12: Environmental Conditions
ENVIRONMENTAL CONDITIONS This instrument is intended for use under the following conditions: 1. indoor use; 2. altitude up to 2 000 m; 3. temperature 5 °C to 40 °C; 4. maximum relative humidity 80 % for temperatures up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C;... -
Page 13: Fuses
FUSES This instrument contains four fuses. All are accessible from the rear-panel. Two protect the AC prime power input, and two protect the internal DC power supplies. The locations of the fuses on the rear panel are shown in the figure below: Fuses #1 and #2 Fuse #4 Fuse #3... -
Page 14: Dc Fuse Replacement
DC FUSE REPLACEMENT The DC fuses may be replaced by inserting the tip of a flat-head screwdriver into the fuse holder slot, and rotating the slot counter-clockwise. The fuse and its carrier will then pop out. FUSE RATINGS The following table lists the required fuses: Recommended Replacement Part Nominal Fuses... -
Page 15: Front Panel Controls
FRONT PANEL CONTROLS 1. POWER Switch . This is the main power switch. When turning the instrument on, there may be a delay of several seconds before the instrument appears to respond. 2. OVERLOAD Indicator . When the instrument is powered, this indicator is normally green, indicating normal operation. - Page 16 units) or -100V to +100V (for -XOS units). The switch below this dial can be used to enable/disable this feature. 6. OUT A Connector . This BNC connector provides the main output of the Channel A amplifier. The output is an amplified version of the input on (3). The gain (V is controlled by (4).
-
Page 17: Rear Panel Controls
REAR PANEL CONTROLS 1. AC POWER INPUT . An IEC-320 C14 three-pronged recessed male socket is provided on the back panel for AC power connection to the instrument. One end of the detachable power cord that is supplied with the instrument plugs into this socket. -
Page 18: General Information
GENERAL INFORMATION BASIC CONTROL The AV-110C-PS-D is a DC-200 kHz variable-gain linear amplifier. The gain of each of the two channels (designated “A” and “B”) is variable from +1 to +50, and is adjusted by rotating the “Gain” associated control. -
Page 19: Operational Check
2) Set the signal generator to produce a ±2V, 10 kHz waveform. (The input impedance of the AV-110C-PS-D is 1 kΩ). Connect a cable from the SYNC connector of the signal generator to the TRIG input of an oscilloscope. Set the oscilloscope to trigger externally. - Page 20 4) Connect one oscilloscope probe (channel 2) to the 10 kΩ load. On the oscilloscope, set the channel 1 vertical scale to 50 V/div, and the horizontal scale to 100 us/div. 5) Set the gain control to minimum (0.0). Turn on the amplifier and the signal generator.
-
Page 21: Mechanical Information
There are no user-adjustable internal circuits. For repairs other than fuse replacement, please contact Avtech (info@avtechpulse.com) to arrange for the instrument to be returned to the factory for repair. Service is to be performed solely by qualified service personnel. -
Page 22: Maintenance
MAINTENANCE REGULAR MAINTENANCE This instrument does not require any regular maintenance. On occasion, one or more of the four rear-panel fuses may require replacement. All fuses can be accessed from the rear panel. See the “FUSES” section for details. CLEANING If desired, the interior of the instrument may be cleaned using compressed air to dislodge any accumulated dust. -
Page 23: Wiring Diagrams
WIRING DIAGRAMS WIRING OF AC POWER M a in s c ir c u i ts - h a z a r d o u s liv e . D o n o t a tte m p t a n y r e p a i r s o n th is in s t r u m e n t b e y o n d t h e fu s e r e p l a c e m e n t p r o c e d u r e s d e s c r i b e d in th e m a n u a l . -
Page 24: Pcb 158N - Low Voltage Power Supply, 1/3
PCB 158N - LOW VOLTAGE POWER SUPPLY, 1/3 p c b 1 5 8 N _ o v p p c b 1 5 8 N _ o v p . s c h + 1 5 V + 1 5 V + 1 5 V B U + B U +... -
Page 25: Pcb 158N - Low Voltage Power Supply, 2/3
PCB 158N - LOW VOLTAGE POWER SUPPLY, 2/3 8 3 0 8 3 5 F U S E H O L D E R 6 4 0 4 4 5 - 6 T P 6 T P 3 T E S T - L O O P T E S T - L O O P S 1 A S 1 B , O R D C... -
Page 26: Pcb 158N - Low Voltage Power Supply, 3/3
PCB 158N - LOW VOLTAGE POWER SUPPLY, 3/3 R 2 1 1 . 5 K o r 1 . 8 K O Y C A P B A N K R 2 6 1 5 K C 2 3 1 0 0 0 u F , 3 5 V ( P 5 1 6 9 - N D ) L 6 2 7 1 1 H V W A R N I N G R 1 7... -
Page 27: Pcb 168B - High Voltage Dc Power Supply
PCB 168B - HIGH VOLTAGE DC POWER SUPPLY HV WA RN ING HV WA RN ING 1 N4 9 3 7 1 N4 9 3 7 6 4 04 4 5 -2 6 4 04 4 5 -2 1 N4 9 3 7 1 N4 9 3 7 1 0 0 OY R1 0... -
Page 28: Main Wiring
MAIN WIRING 1 / 8 A 2 4 - N 3 0 - M E W I T H P C B 1 6 8 1 K , A M P 1 5 K , O S 1 1 K , A M P 2 5 K , O S 2 U V 1 J 2 3 4 - N D S P A C E R S X 2... -
Page 29: Performance Check Sheet
PERFORMANCE CHECK SHEET...
Need help?
Do you have a question about the AV-110C-PS-D and is the answer not in the manual?
Questions and answers