Advertisement
Precautions
• Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
• Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
• Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Removing the protection collar
and the bracket (4)
Before installing the unit, remove the
protection collar 5 and the bracket 1 from
the unit.
1
Remove the protection collar 5.
1 Engage the release keys 6 together with
the protection collar 5.
2 Pull out the release keys 6 to remove the
protection collar 5.
2
Remove the bracket 1.
1 Insert both release keys 6 together
between the unit and the bracket 1 until
they click.
2 Pull down the bracket 1, then pull up the
unit to separate.
Mounting example (5)
Installation in the dashboard
Notes
• Bend these claws outwards for a tight fit, if
necessary. (5-2)
• Make sure that the 4 catches on the protection
collar 5 are properly engaged in the slots of the
unit. (5-3)
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 4.
How to detach and attach the
front panel (7)
Before installing the unit, detach the front
panel.
7-A To detach
Before detaching the front panel, be sure to
press (OFF). Press
, then pull it off towards
you.
7-B To attach
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
After tuning off the ignition, be sure to
press and hold (OFF) on the unit until the
display disappears.
Otherwise, the display does not turn off and this
causes battery drain.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after detaching the
front panel.
使用前注意事項
•仔細選取安裝位置，以使本裝置不干擾正常的駕
駛操作。
•避免將本機安裝在受灰塵，污物和強烈振動影響
的區域，或安裝在高溫處，如直對陽光下或熱氣
管道附近。
•為了安裝安全和可靠，請使用附送的安裝構件。
安裝角度之調整
請在 45 度以內調整安裝角度。
拆下保護環和托架（4）
安裝之前，請先從本裝置上拆下保護環 5 和托架
1 。
1
拆下保護環 5 。
1 將開鎖鑰匙 6 與保護環 5 嚙合。
2 拉出開鎖鑰匙 6 以拆下保護環 5 。
2
拆下托架 1 。
1 將兩把開鎖鑰匙 6 一起插入裝置和托架 1
之間，直至聽到喀嗒聲。
2 向下拉托架 1 ，然後向上拉裝置，使之相
互脫離。
安裝示例（5）
安裝在儀表板裡
註
• 若有必要，則可彎曲這些卡爪。 （5-2）
• 必須將保護環 5 上的 4 個鉤爪正確嚙合在裝置的卡槽
中。 （5-3）
將本機安裝於日本產汽車上時
（6）
有的日本產汽車不能安裝本機，在這種情形下，請
向 Sony 經銷商諮詢。
註
為防止發生故障，安裝時只能使用附送的螺絲 4 。
如何拆卸和裝配前面板（7）
安裝本機之前，請先拆卸前面板。
7-A 拆卸
拆卸前面板之前，須先按下 (OFF) 鍵。
然後，按下
鍵，朝您自己的方向拉出。
7-B 裝配
如圖所示，將前板的 A 處對準本機的 B 處，然
後將左側推入直至聽到喀嗒聲。
安裝在點火鑰匙開關上沒有 ACC
（附件）位置的汽車上時的警告
關閉汽車發動機後，必須按住 (OFF) 不放，
直至顯示消失。
否則顯示不會關閉，並耗費電池。
RESET 按鈕
當安裝和連接完成後，務請用原子筆等按壓 RESET
按鈕，然後拆卸前面板。
Advertisement
