Making An Audio Or A Video Recording - Pioneer Elite VSX-91TXH Operating Instructions Manual

Using other functions
10
Setting What it does
BRIGHT
Adjusts the overall brightness.
(Brightness)
CONTRAST Adjusts the contrast between light
and dark.
HUE Adjusts the red/green balance.
I/P. CONV When Auto is selected, 480i/576i or
(I/P Convert)
480p/576p is automatically selected
depending on the capability of the
display connected to this receiver.
When ON is selected, 480i/576i video
signals are upconverted into 480p/
576p. This feature is only available
when analog signals are converted
into HDMI signals.
A. DELAY This feature automatically corrects
(Auto delay)
the audio-to-video delay between
components connected with an
HDMI cable. The audio delay time is
set depending on the operational
status of the display connected with
an HDMI cable. The video delay time
is automatically adjusted according
to the audio delay time.
a.Only when listening to 2-channel sources in Dolby Pro Logic IIx Music /
Dolby Pro Logic II Music mode.
b.Only when listening to 2-channel sources in Neo:6 Music mode.
c.The initially set AUTO is only available for Dolby TrueHD signals. Select
MAX or MID for signals other than Dolby TrueHD.
d.You shouldn't have any problems using this with most SACD discs, but
if the sound distorts, it is best to switch the gain setting back to 0 dB.
e. This feature is only available when the connected display supports the
automatic audio/video synchronizing capability ('lip-sync') for HDMI. If you
find the automatically set delay time unsuitable, set A. DELAY to OFF and
adjust the delay time manually. For more details about the lip-sync feature
of your display, contact the manufacturer directly.
Note
1 • The receiver's volume, AV parameters, and surround effects have no effect on the recorded signal.
• Some digital sources are copy-protected, and can only be recorded in analog.
• Some video sources are copy-protected. These cannot be recorded.
64
En
Option(s)
–10 to +10
Default: 0
–10 to +10
Default: 0
–10 to +10
Default: 0
OFF
ON
OFF
OFF
ON
e

Making an audio or a video recording

You can make an audio or a video recording from the
built-in tuner, or from an audio or video source
connected to the receiver (such as a CD player or TV).
Keep in mind you can't make a digital recording from an
analog source or vice-versa, so make sure the
components you are recording to/from are hooked up in
the same way (see Connecting your equipment on
page 11 for more on connections).
Since the video converter is not available when making
recordings (from the video OUT jacks) make sure to use
the same type of video cable for connecting your recorder
as you used to connect your video source (the one you
want to record) to this receiver. For example, you must
connect your recorder using S-video if your source has
also been connected using S-video.
For more information about video connections, see
Connecting a DVD/HDD recorder, VCR and other video
sources on page 14.
RECEIVER INPUT
SELECT
XM RADIO SIRIUS
DVD TV
CD-R/TAPE HDMI 2
iPod HDMI 1
1 Select the source you want to record.
Use the input source buttons (or INPUT SELECT).
• If necessary, press SIGNAL SEL (SIGNAL SELECT) to
select the input signal corresponding to the source
component (see Choosing the input signal on
page 29 for more on this).
2 Prepare the source you want to record.
Tune to the radio station, load the CD, video, DVD etc.
3 Prepare the recorder.
Insert a blank tape, MD, video etc. into the recording
device and set the recording levels.
Refer to the instructions that came with the recorder if
you are unsure how to do this. Most video recorders set
the audio recording level automatically—check the
component's instruction manual if you're unsure.
4 Start recording, then start playback of the source
component.
1
SYSTEM OFF
SOURCE
DVR 2
DVR 1 TV CTRL
CD ZONE 2
TUNER RECEIVER