Related Manuals for Hall Technologies HT-AIM-70
Summary of Contents for Hall Technologies HT-AIM-70
- Page 1 Hall Technologies • 1234 Lakeshore Dr Suite #150 Coppell, TX 75019 • halltechav.com HT-AIM-70 4K@60Hz 4:2:0 HDBT Extender USER MANUAL May 24, 2023 Hall Technologies May 24, 2023 Page 1 of 12...
- Page 2 7. Unplug this apparatus during lightning storms or when unused for long periods of time. 8. Protect the power cord from being walked on or pinched particularly at plugs. 9. Only use attachments / accessories specified by the manufacturer Hall Technologies May 24, 2023 Page 2 of 12...
-
Page 3: Table Of Contents
Introduction ..............................4 Overview ............................4 Features............................4 Package Contents ............................4 Connectors & Indicators ..........................5 HT-AIM-70 Front Panel ........................5 HT-AIM-70 Rear Panel ........................6 Product Wiring and Connection Diagram ....................7 Applications ..............................8 Setup ................................9 Installation ............................ -
Page 4: Introduction
Over a Cat5e/6 cable, extends 4K@60Hz 4:2:0 8-bit up to 35m/115ft and 1080P up to 60m/200ft. Bi-directional PoC (Power over Cable) with one power adapter at either end. Supports bi-directional IR and RS232 pass-through. Package Contents HT-AIM-70 1x Transmitter Unit 1x Receiver Unit 1x Power Adapter (DC 18V 1A) ... -
Page 5: Connectors & Indicators
Connectors & Indicators HT-AIM-70 FRONT PANEL Name Description On: The device is powered on. • POWER Off: The device is powered off. • On: The device is working properly. • STATUS Off: The device is not working properly. • On: HDCP protected content is being transmitted. -
Page 6: Ht-Aim-70 Rear Panel
HT-AIM-70 REAR PANEL Name Description POWER DC 18V power supply. (Only one side needs to be powered.) HDBT IN HDBaseT input, connected to the transmitter output via Cat5e/6/7 cable. IR IN Connect either unit to the IR Receiver Cable (Signal is sent to the other unit’s IR OUT). -
Page 7: Product Wiring And Connection Diagram
Product Wiring and Connection Diagram Hall Technologies May 24, 2023 Page 7 of 12... -
Page 8: Applications
Applications A laptop, or other HDMI source, is connected to the HDMI input on the HT-AIM-70-TX and then transmitted over the category cable to the HT-AIM-70-RX, where a display, connected to the HDMI output, shows the HDMI source. Control via RS232 or IR is also passed through the category cable for display control. -
Page 9: Setup
2. The bottom part of the L-bracket will slightly raise the transmitter/receiver and will create a small gap between the device and the mounting surface. 3. Using the appropriate hardware (not included), mount the bottom of the L-brackets to the desired surface. Hall Technologies May 24, 2023 Page 9 of 12... -
Page 10: Troubleshooting
(depending on the desired resolution) Confirm the HDMI input of the display is correctly selected Confirm the connected source is sending video to the HT-AIM (i.e. verify laptop is in duplicate or extend mode) Hall Technologies May 24, 2023 Page 10 of 12... -
Page 11: Specifications
Power Consumption 8.88W (Pair, PoC) Power 1x DC 18V/1A (included) 108.8mm W x 15mm H x 64.2mm D Dimensions (4.3” W x 0.6” H x 2.5” D) Weight 180g (0.4 lbs.) Hall Technologies May 24, 2023 Page 11 of 12... - Page 12 © Copyright 2022. Hall Technologies All rights reserved. 1234 Lakeshore Drive, Coppell, TX 75019 halltechav.com / support@halltechav.com (714)641-6607 Hall Technologies May 24, 2023 Page 12 of 12...