Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Synology NAS RS822+
Summary of Contents for Synology NAS RS822+
- Page 1 Synology NAS RS822+/RS822RP+ Hardware Installation Guide...
-
Page 2: Table Of Contents
Chapter 2: Hardware Setup Tools and Parts for Component Installation Install Drives Start up Your Synology NAS Install a Memory Module on Synology NAS Install PCle Add-in Cards Chapter 3: System Maintenance Replace the Power Supply Unit (PSU) Chapter 4: Install DSM on Synology NAS... -
Page 3: Package Contents
Chapter Before You Start Synology NAS RS822+/RS822RP+ is an enterprise server consisting of both system hardware and the software operating system, DiskStation Manager (DSM). This manual will guide you through all configuration aspects of your RS822+/RS822RP+, including the hardware components, setup procedures, and system maintenance. -
Page 4: Synology Rs822+/Rs822Rp+ At A Glance
1. Press to power on your Synology NAS. Power Button 2. To power off the Synology NAS, press and hold until you hear a beep sound and the Power LED starts blinking. Displays warnings regarding fan or temperature. For more ALERT Indicator information, see "Other LED Indicators". -
Page 5: System Fans
If any fan failure occurs, please refer to the images below to locate the failed fan(s) indicated in DSM. The fans are numbered as below. To replace the failed fan(s), please contact Synology Technical Support at www.synology.com/support technical assistance. For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com. 5 Chapter 1: Before You Start... -
Page 6: System Modes And Led Indicators
System Modes and LED Indicators System Modes and Definitions There are 7 system modes in Synology NAS. The System modes and their definitions are as below: System mode Definition Synology NAS is powering on when you press the power button or restarting when Powering on you run operations in DSM. - Page 7 • Enter hibernation then wake up from hibernation: DSM is ready for use > Hibernation > DSM is ready for use • Shutdown Synology NAS: DSM is ready for use > Shutting down > Powered off • Power failure with UPS attached: DSM is ready for use >...
-
Page 8: Other Led Indicators
HDD/SSD for more information. 2 Please try to restart your Synology NAS or re-insert the drives, then run the HDD/SSD manufacturer's diagnostic tool to check the health status of the drives. If you can sign in to DSM, please run the built-in S.M.A.R.T. -
Page 9: Hardware Specification
• Operating Temperature: 32 to 95˚F (0 to 35˚C) • Storage Temperature: -5 to 140˚F (-20 to 60˚C) • Relative Humidity: 5% to 95% RH Note: Model specifications are subject to change without notice. Please refer to www.synology.com for the latest information. 9 Chapter 1: Before You Start... -
Page 10: Spare Parts
Spare Parts www.synology.com/products/spare_parts Visit if you need to replace system fans, disk trays, or power supply units. Model Name Picture Description Disk Tray (Type R8) 3.5"/2.5" Drive Tray With Lock FAN 40*20_3 System Fan 40*40*20 mm PSU 150W-RP Module_2 Redundant PSU Module 150W... -
Page 11: Safety Instructions
Safety Instructions Keep away from direct sunlight and away from chemicals. Ensure a stable environment with no abrupt changes in temperature or humidity. Place the unit right side up at all times. Keep the unit away from liquids. Before cleaning, unplug the power cord. Do not use chemical or aerosol cleaners. Wipe with damp paper towels. -
Page 12: Chapter 2: Hardware Setup
Please back up any important data before installation. • Rail mounting kit Warning: We suggest mounting your Synology NAS on a cabinet before installing any drives since the heavy weight will increase the installation difficulty. Install Drives Please follow the steps below for drive installation: 1 Pull out the drive tray handle in the direction as shown below. - Page 13 • For 2.5" drives: Place the drive in the drive tray. Flip the tray over and tighten screws into the four spots indicated below to secure the drive in place. 3 Insert the loaded drive tray into the empty drive bay and push it into position. Note: Make sure that the drive tray is completely inserted.
-
Page 14: Start Up Your Synology Nas
Start up Your Synology NAS 1 Connect one end of each power cord to the power ports located on the back of your Synology NAS and the other end to a power outlet. 2 Connect at least one LAN cable to one of the LAN ports and the other end to your switch, router, or hub. -
Page 15: Install A Memory Module On Synology Nas
2 Remove the top cover. 1 Remove the four screws on the top cover of your Synology NAS. 2 Slide open the top cover to the front-end of your Synology NAS, then lift it up and put it aside. Note: When you remove the top cover, sensitive internal components are exposed. - Page 16 Note: • Hold the memory module by its edges and avoid touching the gold connectors. • Synology will not provide full product warranty or technical support if a non-Synology memory module is used for memory upgrade. 5 Place the top cover back and slide it into secure position, then fasten the screws you removed in step 2.
-
Page 17: Install Pcle Add-In Cards
To remove the memory module 1 Follow step 1 to 2 of the "To install the memory module" section to shut down your Synology NAS, disconnect the cables, and remove the top cover. 2 Push the levers on both sides of the memory module outward. The memory module will be released from its slot. -
Page 18: Chapter 3: System Maintenance
By pressing the Beep Off button, you can silence the long beep when it sounds. 2 On the rear panel, push the lever of the PSU inward as shown. 3 Pull the PSU out of your Synology NAS. 4 Prepare a new PSU. Insert it into the empty slot until you hear a click. -
Page 19: Chapter 4: Install Dsm On Synology Nas
3 Enter either of the following into the address bar of your browser: find.synology.com synologynas:5000 4 Web Assistant will be launched in your web browser. It will search for and find the Synology NAS within the Installed. local network. The status of your RS822+/RS822RP+ should be... - Page 20 Section 5. License Limitations. The license set forth in Sections 1, 2 and 3 applies only to the extent that you have ordered and paid for the Product and states the entirety of your rights with respect to the Software. Synology reserves all rights not expressly granted to you in this EULA.
- Page 21 Arbitration Law and related enforcement rules of the country in which Synology Inc. was organized. In such cases, the arbitration will be limited solely to the dispute between you and Synology. The arbitration, or any portion of it, will not be consolidated with any other arbitration and will not be conducted on a class-wide or class action basis.
- Page 22 Section 3. Limited Warranty and Remedies 3.1 Limited Warranty. Subject to Section 3.2, Synology warrants to the Customer that each Product (a) will be free of material defects in workmanship and (b) under normal use will perform substantially in accordance with Synology's published specifications for the Product during the Warranty Period.
- Page 23 Section 4. Limitations of Liability 4.1 Force Majeure. Synology will not be liable for, or be considered to be in breach of or default under this Warranty on account of, any delay or failure to perform as required by this Warranty as a result of any cause or condition beyond its reasonable control (including, without limitation, any act or failure to act by Customer).
- Page 24 Arbitration Association, except as otherwise provided below. The arbitration will be conducted before a single arbitrator, and will be limited solely to the dispute between Customer and Synology. The arbitration, or any portion of it, will not be consolidated with any other arbitration and will not be conducted on a class-wide or class action basis. The arbitration shall be held in King County, Washington, U.S.A.
- Page 25 5.9 Entire Agreement. This Warranty constitutes the entire agreement, and supersedes any and all prior agreements, between Synology and Customer related to the subject matter hereof. No amendment, modification or waiver of any of the provisions of this Warranty will be valid unless set forth in a written instrument signed by the party to be bound thereby.
- Page 26 FCC Declaration of Conformity This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 27 この装置は、クラス A 機器です。この装置を住宅環境で使用すると電波妨 害を引き起こすことがあります。この場合には使用者が適切な対策を講ずる よう要求されることがあります。 VCCI 一 A...