Advertisement
Quick Links
ROOM SERIES
Installation & Operation Instructions
A/10KS-RSO-RJ6
PRECAUTIONS
• DO NOT RUN THE WIRING IN ANY CONDUIT
WITH LINE VOLTAGE (24/120/230 VAC).
MOUNTING INSTRUCTIONS
Separate the cover from the base. Attach the base
directly to the wall or to a standard 2" x 4" junction
box using the (2) #6-32 x 1" screws provided.
Take care when mounting. Check local code for
mounting height requirements. Typical mounting
heights are 48-60" (1.2-1.5 m) o the ground and at
least 1.5' (0.5 m) from the adjacent wall. The sensor
should be mounted in an area where air circulation is
well mixed and not blocked by obstructions.
*Reference FIGURE 2 (p. 2)
For optimal temperature measurement, follow
these tips:
• Do not install on external walls.
• Avoid air registers, di users, vents, and windows.
• Avoid con ned areas such as shelves, closed
cabinets, closets, and behind curtains.
• Eliminate and seal all wall and conduit penetrations.
Air migration from wall cavities may alter
temperature readings.
• A thermally-insulated backing should be used when
tting to solid walls (concrete, steel, etc.). ACI part:
A/ROOM-FOAM-PAD
*Reference FIGURE 3 (next page)
• Do not install near heat sources, eg: lamps,
radiators, direct sunlight, copiers, chimney walls,
walls concealing hot-water pipes.
Refer to the Wiring Instructions (p. 2) to make
necessary connections. After wiring, attach the cover
to the base by snapping the top of the cover on rst
and then the bottom. Tighten the cover down, using
the (2) 1/16" Allen screws located in the bottom of
the housing. A 1/16" Hex driver is needed to secure
the cover to the base.
Automation Components, Inc.
2305 Pleasant View Road | Middleton, WI 53562
Phone: 1-888-967-5224 | Website: workaci.com
FIGURE 1: ROOM DIMENSIONS
ROOM, VERSION 1
[R]
2.75"
(69.85 mm)
FRONT
BOTTOM
ROOM, VERSION 2
[R2]
2.75"
(69.85 mm)
FRONT
BOTTOM
Page 1
Phone: 1-888-967-5224
Website: workaci.com
1.12"
(28.55 mm)
4.50"
(114.30 mm)
RIGHT
1.12"
(28.55 mm)
4.50"
(114.30 mm)
RIGHT
Version: 3.0
I0000329
Advertisement
Related Manuals for aci Room Series
Summary of Contents for aci Room Series
- Page 1 1.12" 2.75" (28.55 mm) (69.85 mm) • A thermally-insulated backing should be used when tting to solid walls (concrete, steel, etc.). ACI part: A/ROOM-FOAM-PAD 4.50" *Reference FIGURE 3 (next page) (114.30 mm) • Do not install near heat sources, eg: lamps,...
- Page 2 FIGURE 2: MOUNTING WIRING INSTRUCTIONS ACI recommends 16 to 26 AWG twisted pair wires or shielded cable for all sensors. Signal OPTIONAL INSULATING GASKET wiring must be run separate from low and high voltage wires (24/120/230 VAC). All ACI thermistors are both non-polarity and non-position sensitive.
- Page 3 • Bad wire connections. WARRANTY The ACI Room Series temperature sensors are covered by ACI’s Five (5) Year Limited Warranty, which is located in the front of ACI’S SENSORS & TRANSMITTERS CATALOG or can be found on ACI’s website: www.workaci.com.
- Page 4 PRODUCT SPECIFICATIONS SENSOR NON-SPECIFIC INFORMATION Number Temperature Sensing Points: Housing Screw Size / Drive Size: 1/16” Allen screws (2 qty) / 1/16” Hex Driver Override Option: Short Set Point (Default) Operating | Storage Temperature Range: 1.5 to 50 °C (35 to 122 °F) | -40 to 65 °C (-40 to 149 °F) Operating Humidity Range: 10 to 95% RH, non-condensing Connections / Wire Size:...